Craftsman 113.299142 Owner's Manual download pdf (Page 5)

WARNING:IF NOT PROPERLY GROUNDED THIS

POWER TOOL CAN INCUR THE POTENTIAL HAZARD

OF ELECTRICAL SHOCK, PARTICULARLY WHEN

USED IN DAMP LOCATIONS, IN PROXIMITY TO

PLUMBING, OR OUT OF DOORS. IF AN ELECTRICAL

SHOCK OCCURS THERE IS THE POTENTIAL OF A

SECONDARY HAZARD SUCH AS YOUR HANDS

CONTACTING THE SAWBLADE.

This saw is equipped with a 3-conductor cord and

grounding type plug which has a grounding prong, approved

by Underwriters' Laboratories and the Canadian Standards

Association. The ground conductor has a green lug and is

attached to the tool housing at one end and to the ground

prong in the attachment plug at the other end.

This plug requires a mating 3-conductor grounded type

outlet as shown.

If the outlet you are planning to use for this saw is of the

two prong type DO NOT REMOVE OR ALTER THE

GROUNDING PRONG N ANY MANNER. Use an adapter

as shown and always connect the grounding lug to a known

ground.

It is recommended that you have a qualified electrician

replace the TWO prong outlet with a properly grounded

THREE prong outlet.

An adapter as shown below is available for connecting plugs

to 2-prong receptacles. The green grounding lug extending

from the adapter must be connected to a permanent ground

such as to a properly grounded outlet box.

GROUNDING LUG

ADAPTER / / __._...

MAKE SURETHIS IS

3-PRONG _ ..,,----- CONNECTEDTO A

PLUGI _ KNOWN GROUND

RECEPTACLE

NOTE: The adapter illustrated is for useonly if you already

have a properly grounded 2-prong receptacle. Adapter is

not allowed in Canada by the Canadian Electrical Code.

The use of any extension cord will cause some loss of

power. To keep this to a minimum and to prevent

over-heating and motor bum-out, use the table below to

determine the minimum wire size (A.W.G.) extension cord.

Use only 3 wire extenston cords which have 3 prong

grounding type plugs and 3-pole receptacles which will

acceot the plug on the saw.

1 H.P. MOTOR 110-120V

Extension Cord Length Wire Size A.W.G.

Upto 50 Ft ................. 14

50to 100 Ft................ 12

100 - 200 Ft ................. 10

200 - 400 Ft. ................ 8

CHECK MOTOR ROTATION

WARNING: FOR YOUR OWN SAFETY, MAKE SURE

PLUG IS NOT CONNECTED TO POWER SOURCE

OUTLET. WHEN CHANGING MOTOR ROTATION,

The motor must rotate CLOCKWISE when viewed from the

shaft end to which you will mount the pulley. (See page

16.) If it does not, change the direction according to the

instructions furnished with the motor.

CONTENTS

WARRANTY ................................. 2

GENERAL SAFETY INSTRUCTIONS

FOR POWER TOOLS ......................... 2

ADDITIONAL SAFETY INSTRUCTIONS

FOR TABLE SAWS ........................... 3

MOTOR SPECIFICATIONS AND ELECTRICAL

REQUIREMENTS ............................ 4

UNPACKING AND CHECKING CONTENTS ........ 6

Tools Needed ................................ 6

List of Loose Parts ............................ 6

ASSEMBLY .................................. 7

Installing Tilt Crank .......................... 7

Checking Table Insert ......................... 7

Checking Blade Squareness to Table .............. 8

Assembling Steel Legs ......................... 8

Mounting Saw ............................... 9

Attaching Table Extensions ..................... 9

Installing Rip Fence Guide Bars ................. 10

Aligning Rip Fence .......................... 12

Adjusting Rip Scale Pointer .................... 13

Repositioning Rip Fence Guide Bars ............. !3

Installing Blade Guard ........................ 14

Mounting the Motor ......................... 16

Installing Belt Guard ......................... 18

Plugging in Motor ........................... 19

GETTING TO KNOW YOUR SAW ............... 20

On-Off Switch .............................. 20

Elevation Crank ............................. 21

Tilt Crank ................................. 21

Tilt Lock Handle ............................ 21

Rip Fence ................................. 21

Miter Gauge ................................ 21

Blade Guard ................................ 21

Table Insert ................................ 21

Removing and Installing Saw Blade .............. 22

Exacti-Cut ................................. 22

BASIC SAW OPERATION USING THE MITER GAUGE23

Work Helpers ............................... 23

Crosscutting ................................ 24

Repetitive Cutting ........................... 24

Miter Cutting ............................... 25

Bevel Crosscutting ........................... 25

Compound Miter Cutting ...................... 25

BASIC SAW OPERATION USING THE RIP J:ENCE .. 26

Ripping ................................... 26

Bevel Ripping .............................. 26

Resawing .................................. 28

Cutting Panels .............................. 28

Rabbeting ................................. 28

ADJUSTMENTS .............................. 29

Miter Gauge ................................ 29

Heeling Adjustment or Parallism of

Sawblade to Miter Gauge Groove ............... 29

Blade Tilt, or Squareness of

Blade to Table ............................. 30

Tilt Mechanism ............................. 32

MAINTENANCE ............................. 32

LUBRICATION .............................. 33

RECOMMENDED ACCESSORIES ............... 33

TROUBLE SHOOTING ........................ 34

REPAIR PARTS .............................. 36

1 2 3 4 5 6 7 8 9 10 ... 43 44

Comments to this Manuals

No comments

Craftsman 113.299142 Owner's Manual Page 5

Comments to this Manuals

Related products and manuals for Power tools Craftsman 113.299142