Craftsman 113.299142 Owner's Manual download pdf (Page 4)

B. Never use grinding wheels, abrasive cut-off wheels,

friction wheels (metal slitting blades) wire wheels or

buffing wheels.

11. USE ONLY ACCESSORIES DESIGNED FOR THIS

SAW,

12. Cross-cutting operations are more conveniently worked

and with greater safety if an auxiliary wood facing is

attached to the miter gauge using the holes provided,

13. Make sure the top of the arbor or cutting tool rotates

toward you when standing in norm_ operating

position. Also make sure the cutting tool, arbor collars

and arbor nut are installed properly. Keep the cutting

tool as low as possible for the operation being

performed. Keep all guards in place whenever _ossible.

14. Do not use any blade or other cutting tool marked for

an operating speed less than 3450 RPM. Never use a

cutting tool larger in diameter than the diameter for

which the saw was designed. For greatest safety and

efficiency when ripping, use the maximum diameter

blade for whicl_ the saw is designed, since under these

conditions the spreader is nearest the blade.

15. Adjust table inserts flush with the table top. NEVER

operate the saw unlessthe proper insert is installed.

16. THINK SAFETY.

Safety is a combination of operator common sense and

alertness at all times when the saw is being used.

17. NOTE AND FOLLOW SAFETY INSTRUCTIONS

THAT APPEAR ON THE FRONT OF YOUR SAW.

DANGER

FOR YOUR OWN SAFETY

READ AND UNDE RSTAND OWNER'S MANUAL

BEFORE OPERATING MACHINE:

I. WEAR SAFETY GOGGLES

2, USE SAW-BLADE GUARD FOR "THRU-SAWING"

3. KEEP HANDS OUT OF PATH OF SAWBLADE

4. USE A"PUSH-STICK" WHEN REQUIRED

5. KNOW HOW TO AVOID "'KICKBACKS'"

6. DO NOT PERFORM OPERATIONS "FREEHAND"

18. WARNING: DO NOT ALLOW FAMILIARITY

(GAINED FROM FREQUENT USE OF YOUR SAW)

TO BECOME COMMONPLACE. - ALWAYS

REMEMBER THAT A CARELESS FRACTION OF A

SECOND IS SUFFICIENT TO INFLICT SEVERE

INJURY.

19. WARNING: THE 2-1/2" SAW PULLEY AND THE

2-1/2" MOTOR PULLEY FURNISHED, WILL RUN

THE BLADE AT APPROXIMATELY 3450 RPM

WHEN USED WITH A 3450 RPM MOTOR. NEVER

SUBSTITUTE THESE PULLEYS TO INCREASE THIS

SPEED BECAUSE IT COULD BE DANGEROUS.

The operation of any power tool can result in foreign

objects being thrown into the eyes, which can result in

severe eye damage. Always wear safety gogglescomplying

with ANSI Z87.1 (shown on Package) before commencing

power tool operation. Safety Gogglesare available at Sears

retail or catalog stores.

MOTOR SPECIFICATIONS AND

ELECTRICAL REQUIREMENTS

This saw is designed to use a 3450 RPM motor only. Do not

use any motor that runs faster than '3450 RPM, It is wired

for operation on 110-120 volts, 50 Hz., alternating current.

IT MUST NOT BE CONVERTED TO OPERATE ON 230

VOLTS. EVEN THOUGH SOME OF THE

RECOMMENDED MOTORS ARE DUAL VOLTAGE.

The outlet in the switch box will accept either a 15 amp. or

a 20 amp. motor plug.

RECOMMENDED CRAFTSMAN MOTORS FOR USE ON

THIS SAW.

No.

H.P. R.P.M. Volts Catalog

1 3450 110.120 1217

1 3450 110.120 1220

If power cord is worn or cut, or damaged in any way, have

it replaced immediately.

If your saw is for use on less than 150 volts it has a plug

that looks like below.

3-PRONG PLUG

GROUNDING PRONG

PROPERLY GROUNDED

3-PRONG OUTLET

See recommendation on saw for use in Canada

CAUTION: Do not use blower or washing machine motors

or any motor with an automatic reset overload protector as

their use may be hazardous.

CONNECTING TO POWER SOURCE OUTLET

This saw must be grounded while in use to protect the

operator from electrical shock.

Plug power cord into 110-120V properly grounded type

outlet protected by a 15-amp. time delay or Circuit-Saver

fuse or circuit breaker.

IF YOU ARE NOT SURE THAT YOUR OUTLET IS

PROPERLY GROUNDED, HAVE IT CHECKED BY A

OUALI FlED ELECTRICIAN.

WARNING: DO NOT PERMIT FINGERS TO TOUCH

THE TERMINALS OF PLUG WHEN INSTALLING OR

REMOVI_IG THE PLUG TO OR FROM THE OUTLET.

1 2 3 4 5 6 7 8 9 ... 43 44

Comments to this Manuals

No comments

Craftsman 113.299142 Owner's Manual Page 4

Comments to this Manuals

Related products and manuals for Power tools Craftsman 113.299142