Craftsman 113.206933 Owner's Manual download pdf (Page 4)

beyond

the :desired

15. Never leave the Jo "work area:with the

power on, before the Jo nter-Planer has come to a

complete stop; Or without removing and storing the

switch key. :

t6: Never operate the Jointer-Pla ner with protective cover

on the unused shaft end of the motor removed.

17. Do not attempt to perform an abnormal or little-used

operation without study and the use of adequate hold

downtpush blocks, jigs, fixtures, stops, etc.

18: DO NOT perform layout, assembly, or setup work on

the table white the cutting _ool is rotating,

WARNING_ THE 2" JOINTER-PLANER PULLEY AND

THE 2-1/2" MOTOR PULLEY FURNISHED WILL RUN

THE CUTTER HEAD AT APPROXIMATELY 4300 RPM

ns for jointer-pmaner

EN USED WITH A 3450 RPM MOTOR, NEVER

SUBSTITUTE OTHER PULLEYS TO INCREASE THIS

SPEED BECAUSE iT COULD BE DANGEROUS.

WARNING: DO NOT ALLOW FAMILIARITY (GAINED

FROM FREQUENT USE OF YOUR JOINTER-PLANER)

BECOME COMMONPLACE. ALWAYS REMEMBER

THAT A CARELESS FRACTION OF A SECOND IS

SUFFICIENT TO INFLICT SEVERE INJURY.

19. Read and follow the instructions appearing on the

danger label on the cutter guard.

DANGER - FOR YOUR OWN SAFETY

READ AND UNDERSTAND OWNER'S

MANUAL SEFORE OPERATING MACHINE

1. WEAR SAFETY GOGGLES PER ANSI Z87.f AT ALL TIMES.

2, NE_VER PERFORM A JOINTING OR PLANING OPERATION WITH CUTTER

HEAD OR DRIVE GUARD REMOVED.

3. NEVER MAKE A JOINTING OR PLANING CUT DEEPER THAN 1/8 INCH,

4, ALWAYS USE HOLD DOWN/PUSH BLOCKS FOR JOINTING MATERIAL

NARROWER THAN 3 INCP_ES, OR PLANING MATERIAL THINNER THAN 3

INCHES.

WEAR YOUR

The operation of any power tool can result in foreign

objects being thrown into the eyes. which can result in

severe eye damage. Always wear safety gogg les complying

with ANSI Z87.1 (shown on Package) before commencing

power too_ operation, Safety Goggles are available at

Sears retail or catalog stores.

contents

POWER TOOL GUARANTEE . . ...... 2

GENERAL SAFETY INSTRUCTIONS FOR

POWER TOOLS ............... ................. 2

ADDITIONAL SAFETY INSTRUCTIONS FOR

JOINTER-PLANER ............................. 3

MOTOR SPECIFICATIONS AND ELECTRICAL

REQUIREMENTS.. ............................ 5

Connecting to Power Source Outlet ............. 5

Check Motor Rotation ......................... 5

UNPACKING AND CHECKING CONTENTS ......... 6

ASS EMB LY ..................................... 7

Assembling Steel Legs ........................ 7

Mounting Jointer-Planer On Recommended

Craftsman Leg Set .......................... 8

Checking Cutterblades and Screws ..............

Mounting Switch .............................. 9

Installing Motor, Pulley, V-Belt and Belt Guards...9

Fence Locks and Stops ...................... 12

Fence Tilt Scale ............................ 12

Cutter Guard ............................... 13

Infeed Table ................................ 14

On-Off Switch .............................. 16

BASIC JOINTER-PLANER OPERATION ........... 17

Feeding the Workpiece ........................ 17

Using the Hold Down/Push Blocks ............. 18

Beveling ................................... 19

MAINTENANCE ................................ 19

Replacing Cutter Blades ..................... 19

Installing Cutter Guard Spring ................ 21

Sharpening Cutter Blades .................... 23

GENERAL MAINTENANCE ...................... 23

LU BRfCATI ON ................................. 23

MOTOR MAINTENANCE AND LUBRICATION ...... 24

TROUBLE-SHOOTING .......................... 24

Installing Sliding Guard ...................... 10 REPAIR PARTS ................................ 26

GETTING TC) KNOW YOUR JOINTER-PLANER. ,o, .11 RECOMMENDED ACCESSORIES ................. 31

DePth of CutHandWhee_ . :. _... ,_ .... .... ;* -o! 1

1 2 3 4 5 6 7 8 9 ... 31 32

Comments to this Manuals

No comments

Craftsman 113.206933 Owner's Manual Page 4

Comments to this Manuals

Related products and manuals for Power tools Craftsman 113.206933