Craftsman 113.213170 Owner's Manual

fSave This Manual "_For Future Referenceowner's ,manualSP5188MODELNO.113.213170DRILL PRESSWITHMAXIMUM DEVELOPED1 I/2 HP MOTORiSerialNumberMo

assemblyWARNING: FOR YOUR OWN SAFETY, NEVER CON*NECT PLUG TO POWER SOURCE OUTLET UNTILALL ASSEMBLY STEPS ARE COMPLETED.TOOLS NEEDED *I.._.l'"

INSTALLING THE TABLE! Loosen support lock and ra=se table support 10ytumRngtable crank clockwise unbl support =s at aworking height level. Tighten sup

1. Locate four (4) 8mm,t, DJa x 20ram long hex head _f,f . : . _S_//UOTOR---bolts, eight (8)flat _vashers, and four (4) hex nuts /" _, z_.,,_&apo

5Locate center pulley assembly tn !oose parts bagand place inproper holeSPINDLE PULLEY6. Locate two (2) V-belts in the loose parts bag.7. Use speed ch

MOTOR CONNECTIONSWARNING: FOR YOUR OWN SAFETY, NEVER CON-NECT PLUG TO POWER SOURCE OUTLET UNTILALL ASSEMBLY STEPS ARE COMPLETED,t. Open motor connecto

2. Slide the chuck up over the arbor as illustrated."="---- SPINOLEARBORm\\i i4. Unlock support lock and raise table so its abouttwo (2) inc

INSTALLING LIGHT BULB1. Install a light bulb (not larger than 60 watt) into thesocket inside the head.ADJUSTING THE TABLE SQUARETO HEADNOTE: The combi

getting to know your drill pressFEED SPRINGADJUSTMENTFEEDSPRING17SPRINGCAPSWITCH1BELT GUARD4" .m==,._,2BELT TENSIONLOCK HANDLE23SUPPORT LOCK18CHU

This Drill Press has 16 speeds as hsted Cerow200RPM 640RPM 1820RPM290RPM 720RPM 2380RPM350RPM 800RPM 2540RPM430RPM 870RPM 3630RPM500RPM 1440RPM580RPM

27 DRILL "ON-OFF" SWITCH ... Has locking fea-ture. THIS FEATURE IS INTENDED TO HELPPREVENT UNAUTHORIZED AND POSSIBLEHAZARDOUS USE BY CHILDRE

FULL ONE YEAR WARRANTY ONCRAFTSMAN DRILL PRESSIf within one year from the date of purchase, this Craftsman Drill Press fails due to a defectin materia

DRILLING TO A SPECIFIC DEPTHTo drill a BLIND hole (no! all the way lhrough) to agiven depth, proceed as follows.1. Mark the deplh of lhe hole on the s

3 Turn the depth scale clockwise until it stops.4, Tighten the depth scale lock,5. The chuck will now be held at this depth when thefeed handles are r

RE-INSTALLING THE CHUCK AND ARBORt. Clean thetapered surfaceonthearborwitha cleancloth.Make surethereare noforeignparticlesstick-ing to the surface. T

basic drill press operationFollow the following mstructlons for operating your drdlpress tO get the best results and to m_mmize the likeli-hood of per

POSITIONING TABLE AND WORKPIECELock the table to the column in a position so that thetip of the drill is just a little above the top of the work-piece

TILTING TABLETo use the table in a bevel (hired) pos_l_on, loosen theset screw under table bevel lock wath Hex "L" wrench.Loosen bevel lock

maintenanceWARNING FOR YOUR OWN SAFETY, TURNSWITCH "OFF" AND REMOVE-PLUG FROM POWERSOURCE OUTLET BEFORE MAINTAINING OR LUB-RIC.a,TING YOUR D

trouble shootingWARNING: FOR YOUR OWN SAFETY, TURN SWITCH "'OFF" AND ALWAYS REMOVE PLUG FROIM POWERSOURCE OUTLET BEFORE TROUBLE SHOOTIN

m4344PARTS LIST FOR CRAFTSMAN 17" DRILL PRESSMODEL NO. 113.213!704748495O51 524342 413O322828312627FIGURE 125\2423354113142221152O1016//19171414&

Key PartNo. No._11 I I1 81732O2 8173913 8173164 8173035 8173476 817774-17 8173438 8173469 81730010 81729911 81734412 813249-12813 STD85200514 81675515

additional safety instructions for drill pressesWARNING: FOR YOUR OWN SAFETY, DO NOTUSE YOUR DRILL PRESS UNTIL IT IS COM-PLETELY ASSEMBLED AND INSTALL

repair partsPARTS LIST FOR CRAFTSMAN 17" DRILL PRESSMODEL NO. 113.21317012\17I81110L9Always order by Part Number--Not by Key NumberFIGURE 2Key Pa

repair partsPARTS LIST FOR CRAFTSMAN 17" DRILL PRESSMODEL NO. 113.213170OJ 1105Always order by Part Number--Not by Key NumberFIGURE 3KeyNo.II1 81

repair partsPARTS LIST FOR CRAFTSMAN 17" DRILL PRESSMODEL NO. 113.213170jl18 I i 38t.n-=o..._L(1)10Always order by Part Number--Not by Key Number

NOTES33

NOTESI I34

NOTES35

/-f8EARSowner'smanualSERVICEMODEL NO.113.213170DRILL PRESS WITHMAXIMUMDEVELOPED1 I/2 HP MOTORHOW TO ORDERREPAIRPARTSJMOTORIZED47-1NCHFLOOR MODEL

b Drum sanders must NEVER be operated onth=s drill press at a speed greater than 1800RPM.c. Do not=nstatlor use any drillthat exceeds 7""_nl

glossary of termst. WorkpieceThe =ternon wh=chthe cutting operations_s beingperformed.2. DrillThe cuttingtoolused in the drill press to make holes=na

motor specifications and electrical requirementsMOTOR SPECIFICATIONSTh_s drill press _s designed to use a 1725 RPM motoronly Do not use any motor that

unpacking and checking contentsWARNING: TO AVOID INJURY FROM UNEX-PECTED STARTING OR ELECTRICAL SHOCK, DONOT PLUG THE POWER CORD INTO A SOURCEOF POWER

LLStof Loose Parts =nBox 507864Item Description Qty.A Feed Handle ... 3B Key Drift ... tC Wrench Hex "L" M3 ...

location and function of controls1. BELT TENSION HANDLE... Turn handle counterc!ockwfse to apply tens,on to belt. turn handleclockw,se to release belt