Craftsman 113.213850 Owner's Manual download pdf (Page 3)

other part that is damaged should be careful-

ly checked to ensure that it will operate pro-

perly and perform its intended function.

Check for alignment of moving parts, binding

of moving parts, breakage of parts, mounting,

and any other conditions that may affect its

operation. A guard or other part that is

damaged should be properly repaired or

replaced.

2t. DIRECTION OF FEED

Feed work into a blade or cutter against the

direction of rotation of the blade or cutter

only.

22. NEVER LEAVE TOOL RUNNING

UNATTEN DED

Turn power off. Don't leave tool until it

comes to a complete stop.

additional safety

instructions for drill presses

WARNING: FOR YOUR OWN SAFETY, DO NOT

ATTEMPT TO OPERATE YOUR DRILL PRESS

UNTIL IT !S COMPLETELY ASSEMBLED AND

iNSTALLED ACCORDING TO THE INSTRUC-

TIONS...AND UNTIL YOU HAVE READ AND

UNDERSTAND THE FOLLOWING:

Page

1. General Safety instructions for Power Tools. 2

2. Getting to Know Your Dri!l Press ........... 12

3. Basic Drill Press Operation ................ 15

4. Adjustments .............................. t7

5. Maintenance .............................. 18

6. Stability of Dri!l Press

The drill press should be bolted to the floor;

an alternate is to securely bolt a piece of

1t2" exterior plywood to the underside of the

Base, extending to both sides, and to rear if

desired.

If the workpiece is too large to support with

one hand, provide an auxiliary support.

Location

The drill press should be positioned so

neither the operator nor a casual observer is

forced to stand in line with a potential Kick-

back.

8. Kickback

A kickback occurs when the workpiece is

suddenly thrown in the OPPOSITE direction

to the DIRECTION OF FEED; THIS CAN

CAUSE SERIOUS INJURY. Kickbacks are

most commonly caused by:

a. Relaxing your grip of the workpiece while

surfacing or planing.

b. Taking too heavy a cut while surfacing or

planing.

c. Ignoring the instructions for surfacing or

planing.

9. Protection: Eyes, Hands, Face, Ears, Body

WARNING: FOR YOUR OWN SAFETY, DO

NOT WEAR GLOVES, NECKT!E OR LOOSE

CLOTHING, AND TiE BACK LONG HAiR

WHEN OPERATING DRILL PRESS.

a. if any part of your drill press is malfunc-

tioning, has been damaged or broken...

such as the motor switch, or other operat-

ing control, a safety device or the power

cord.., cease operating immediately until

the particular part is properly repaired or

replaced.

ANSI Z87.1, and a face mask if operation

is dusty. Wear ear plugs or muffs during

extended periods of operation.

c. Never place your fingers in a position

where they could contact the drill or other

cutting tool if the workpiece should

unexpectedly shift.

d. To avoid injury, follow instructions exactly

as given and shown in adjusting spring

tension of quill.

e. ALWAYS position backup material to con-

tact the left side of the column. POSITION

workpiece to butt against the column

whenever possible--if it is too short,

clamp solidly to the Table. Use table slots

or clamping ledge around outside edge of

Table. This is to prevent the drill bit from

grabbing the work from your hands. This

action would cause the workpiece to spin

with the drill, and could cause serious

injury. A drill press vise must be fastened

to the table.

f. Never perform any operation "free-hand"

.(hand-holding workpiece rather than sup-

port it on the Table), except when polish-

ing -- Wear Safety Goggles!

g. Securely lock Head and Support to Co!-

umn, Arm to Support, and Table to Arm

before operating Drill Press.

h. Never perform any operation by moving

the Head or Table with respect to one

another.

i. Before pulling the motor switch "ON", be

positive the belt guard is closed, the

Chuck is installed properly, and the drill or

other cutting tool is securely clamped in

the chuck.

j. Before starting the operation, jog the

motor switch to be sure the drill or other

cutting toot does not have excessive run-

out or cause vibration.

k. Do not operate the Dril! Press unless the

Depth Stop and Stop Nut are installed.

I. Use the spindle speed recommended for

the specific operation and workpiece

materia! - refer to panel on left side of

the Head for drilling information; for

accessories, refer to the instruction sheets

that accompany the accessories.

m. tf workpiece overhangs the Table such that

it will fall to floor if unsupported, clamp it

to the Table or provide auxiliary support,

1 2 3 4 5 6 7 8 ... 23 24

Comments to this Manuals

No comments

Craftsman 113.213850 Owner's Manual Page 3

Comments to this Manuals

Related products and manuals for Power tools Craftsman 113.213850