Craftsman 113.213850 Owner's Manual download pdf (Page 13)

This Drill Press has 12 speeds as listed

below:

300RPM 1450RPM

375RPM 1530RPM

525RPM 2000RPM

560RPM 2200RPM

700RPM 3400RPM

860RPM 4600RPM

Seeright side of Headfor specificplacement

of beltson pulleys.

® SPINDLE SPEEDS iN R.P.M. ¢_

3OO

,,,._, 700

o ,

2000

¢

375

860

2200

525 560

1450 1530

3400 4600

1. BELT GUARD ...Covers pulleys and belt

during operation of drill press.

2. BELT TENSION HANDLEoo.Turn handle

counter c_ockwise to apply tension to belt,

turn handle clockwise to release belt tension.

3. BELT TENSION LOCK HANDLES... Tighten-

ing handles locks motor bracket support and

BELT TENSION HANDLE to maintain correct

belt distance and tension.

4. HEAD LOCKS.., Lock the head to the col-

umn. ALWAYS have them locked in place

while operating the drill press.

5. COLUMN COLLAR... Holds the rack to the

column. Rack remains movable in collar to

permit table support movements.

6. RACK... Combines with gear mechanism to

provide easy elevation of table by hand oper-

ated table crank.

7. SUPPORT LOCK...Tightening locks table

support to column. Always have it locked in

place white operating the Drill Press.

8. TABLE CRANK... Turn clockwise to elevate

table. Support lock must be released before

operating crank.

9. TABLE SUPPORT... Rides on column to

support arm and table.

10. BASE .o.Supports Drill Press. For additional

stability, holes are provided in base to bolt

Drill Press to floor. (See "Additional Safety

Instructions for Drill Presses").

11. COLUMN SUPPORT,..Supports column,

guides rack, and provides mounting holes for

column to base.

12. COLUMN ... Connects head, table, and base

on a one-piece tube for easy alignment and

movement.

13. BEVEL SCALE ... Shows degree table is tilt-

ed for bevel operations. Scale is mounted on

side of arm.

14.

15.

16.

17.

18.

19.

20.

ARM ...Extends beyond table support for

mounting and aligning the table.

TABLE BEVEL LOCK... Locks the table i_

any position from 0°-45 °.

TABLE LOCK... Table can be rotated in var'_-

ous positions and locked.

TABLE... Provides working surface to sup-

port workpiece.

FEED HANDLE... For moving the quill up o_

down. One or two may be removed if neces-

sary whenever the workpiece is of suoh

unusual shape that it interferes with the

handles.

CHUCK.,, Holds drill bit or other recor'n-

mended accessory to perform desired opera-

tions,

CHUCK LOCKING COLLAR... Draws the

chuck onto the spindle nose. It prevents the

chuck from coming loose during operatiorl.

ALWAYS have the collar tightened.

21. FEED STOP ROD... Holds stop nuts for dri t l*

ing to specific depths.

22. STOP NUTS... Limits the downward move-

ment of the quill at any desired point with _n

its travel, and prevents the pointer from mov-

ing upward.

23. DEPTH POINTER.,. Indicates drilling depth

and is located between stop nuts.

24. DEPTH SCALE,,. Shows depth of hole beir_ _

drilled,

25. SPRING CAP.,, Provides means to adju,_t

quill spring tension.

26, LIGHT "ON.OFF" SWITCH...Separate

switch to operate light independent of dr_it

switch. This permits the light to be "or_,,

while making setups,

13

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 ... 23 24

Comments to this Manuals

No comments