Craftsman 113.29461 Owner's Manual

[Sears ]ownersmanualCAUTION:Read SAFETYRULES andINSTRUCTIONScarefullyMODEL NO.113.29461IO-INCHRADIAL SAWassembly • operating • repair partSEARS, ROEBU

assembly and adjustments7. Adjusting the Rip-Scale Indicators (Figures 26 --29)NOTE: The two rip scales and indicators areintended only for use in mak

electrical connectionsmounting bracket, shift the spreader into alignmentwith the saw blade, then retighten the two screws tohold the bracket securely

electrical connections3. Connections for 240V A.C. (Figure 32)a. The wires inside the motor terminal box must beconnected as fo!lows:(1) The orange-co

U_,_t;_l Lt i ili_ LUlilIUI_LOCATIONS AND FUNCTIONS OF CONTROLS781. Arm-Latch Lever2, Swivel Latch-Pin Knob3. Rip Scale and Indicator4. Miter Scale an

operating controls(1) If the radial arm is already indexed, rotate thearm-latch handle ( 18, figure 34) 1!4turn counter-clockwise from the locked posi

basic saw operationsthe pawls and attempting to slide it in the directionof kickback. If the pawls do not catch, furtheradjustment is necessary.ed.e.W

basic saw operationsRADIAL ARMRADIALARMCARRIAGEFigure 37ARMFigure 38OPERATION NO. 2 -- MITER CROSSCUTMiter crosscutting is the process of sawing a boa

YOKEFigure 426. Blade should be sharp and correctly set.7. Hands must be kept wellaway from saw blade.8. When ripping narrow or short stock, always us

safety instructions to operator1. Be sure to read the following instructions carefullybefore operating the saw.WARNING: DO NOT CONNECT POWERCORD UNTIL

12. Gloves should not be worn while operating the saw.Loose flowing garments, jewelry (rings, wrist watches,etc.} and neckties should never be worn. L

general safety rules for power tools1. KNOW YOUR POWER TOOLRead the owner's manual carefully. Learn its appli-cation and limitations as well as t

trouble shootingTROUBLE SHOOTINGEven though the finest materials and precision workman-ship have been incorporated into your Craftsman saw, it isreaso

trouble shootingthe top surface of the table, as described under"ALIGNMENT INSTRUCTIONS", step "2. Adjust-ing the Table Supports Parall

F,gu,o,8!SOCKET HDSCREW(4 Tolal)_ BEVELINDEXSCALE)) BEVELINDICATORILOCK KNOB(b) Using a 1/4-inch hex-L wrench, slightlyloosen the four socket-head scr

trouble shootingYOKE CLAMP LOCKING POSITIONASSEMBLY -, DUE TO WEAR""__ ._ _p...NO R MA L LOCKINGPOSITION_------_'_ LOOSENEDPOSITION_..

LEFT-HD,COVERRIPFENCEa. Evidence of Blade Heel(1) CrosscuttingFigure 58(a) Heeling to the right will tend to slide theworkpiece toward the right along

trouble shooting - motorPERIODICALLY LUBRICATE THESE POINTSUse SAE No. 10W-30 automotive engine oil. Refer to theParts Lists for locations, and lightl

TROUBLE SHOOTING CHART--MOTOR (Con't. ITROUBLE PROBABLE CAUSE IqMotor overheats. 1. Motor overloaded.2. Improper cooling. (Air cir-culation restr

POWER TOOL GUARANTEECraftsman power tools (or welders) are unconditionallyguaranteed for one year to give complete satisfaction or thetool will be rep

repair partsCRAFTSMAN IO-INCH RADIAL SAW, MODEL NO. 113.2946133SEE FIGURE 2FOR EXPLODEDSEE FIGURE 5 ._FOR EXPLODED VIEW 2526FIGURE I28

PARTS LISTCRAFTSMAN IO-INCH RADIAL SAW, MODEL NO. !13.29461All parts illustrated in Figures 1 through 5 and listed under part numbers may be ordered t

unpacking and preassemblyCONTENTSPageUnpacking and Preassembly Instructions ... 3Alignment Instructions ... 5Electrical Connections .

repair partsCRAFTSMAN IO-INCH RADIAL SAW, MODEL NO. 113.29461.1-4v/,._31SEE FIGURE 4 46/"FOil EXPLODEDv,EW 6,3 45I1I3235FIGURE 23O

CRAFTSMAN IO-INCH RADIAL SAW, MODEL NO. 113.29461FIGURE 2 PARTS LISTKey Pa_No. No.1 305662 631203 3O5674 4366645 632156 634157 634168 3O5309 9415819I0

Qrepatr partsCRAFTSMAN IO-INCH RADIAL SAW, MODEL NO. 113.29461301292O15242322I 11I16 15 FIGURE318FIGURE 3 PARTSLISTKey PartNo. No. Description1 63411

repa,r partsCRAFTSMAN IO-INCH RADIAL SAW, MODEL NO. 113.294611516FIGURE 4 PARTS LISTKey PartNo. No.- 63490- 634911 4480032 634372 634893 634384 448011

repair partsCRAFTSMAN 10-INCH RADIAL SAW, MODEL NO. 113.294615 6I3132101213/1421FIGURE 534

CRAFTSMAN 10-INCH RADIAL SAW, MODEL NO. 113.29461FIGURE 5 PARTS LISTKey PartNo. No. Description2345689101112131415161718192O21222324251027186307863077

Searso wnersmanualMODEL NO.113.29461SearsSERVICEis atYOURSERVICEwherever YOUlive or movein the U.S.A.How to ORDER Repair,The Model Number will be foun

unpacking and preassembly2. Mounting Your Saw on a WorkbenchMount on a Craftsman Power Tool Base or a sturdy, flatbench, in such a position that the e

assembly and adjustmentsALIGNMENT INSTRUCTIONSGUARD ASSEMBLYLOCK KNOBGUABDCLAM_SCREW;HT RECEPTACLELATCH-PIN HANDLEBEVEL LOCK KNOBFigure 5NOTE: The fol

assembly and adjustmentsLATCH-PINHANDLEFigure 10Figure 7ARM-LATCH HANDLEFigure 8Figure 9MOUNTING SCREW-FRONT MOUNTING SCREWL-H TABLE SUPPORTd.Loosen b

U-CLIPBASECROSS-MEMBER Figure1/k. Adjust the right-hand table support in exactly thesame manner, without altering the radial-arm eleva-tion setting.Lo

assembly and adjustments4. Squaring the Crosscut Travel (Figures 16 through 23)a. Loosen the carriage lock knob, move the carriage tothe approximate c

MITERSCALEATTACHINGSCREWS 0 oMARKFigure 21Figure 22MITERSCALEit'q[MITER SCALEINDICATORFigure 23g. Now slowly move the carriage outward along ther