Craftsman 351.217881 Operations Instructions download pdf (Page 6)

EXTENSIONCORDLENGTH

WireSize A.W.G.

Upto 50ft.................................. 16

50-100ft................................... 14

NOTE:Usingextensioncordsover100ft.longisnot

recommended.

MOTOR

The 120 Volt AC universal motor has the following

specifications:

Voltage ................................... 120

Amps ..................................... 12

Hertz ..................................... 60

Phase .................................. Single

Cutterhead RPM ......................... 10,000

ELECTRICAL CONNECTIONS

WARNING: Make sure unit is turned off and discon-

nected from power source before inspecting any wiring.

The motor is assembled with an approved three con-

ductor cord to be used on 120 volts as indicated. The

power supply to the motor is controlled by a double

pole locking rocker switch.

• Remove the key to prevent unauthorized use.

The power lines are inserted directly onto the switch.

The green ground line must remain securely fastened

to the frame to properly protect against electrical shock.

Refer to Figures 10-20, pages 7-9.

DESCRIPTION

Craftsman 61/8'' jointer/planer is used to surface the

faces and edges of boards, produce a flat surface on

warped boards and shape bevels, chamfers and tapers.

The jointer/planer features cast iron infeed and outfeed

tables, cast iron body with smooth work surfaces and

lead screws for precise table height adjustment.

Balanced guide fence tilts 45 ° (inward) and 45 ° (out-

ward). Built-in blower for chip removal. Tool comes with

locking rocker switch with removable key and push

blocks. Jointer/planer easily handles rough-cut lumber,

planes hard and soft woods up to 61/8'' wide using a two

blade cutterhead, and takes cuts up to 1/8".

SPECIFICATIONS

Table size ............................ 285/8x 61/4"

Fence size ........................... 22%x 33/4"

Blade width ............................... 61/J'

Maximum cut ........................... 1/8"Deep

Cuts Per Minute ......................... 20,000

Overall Size ....................... 285/8x 18 x 12"

Dust collection port .................. 2V2" Diameter

Weight .................................. 70 Ibs

Motor ............................... 12A, 120V

OPERATION SAFETY RULES

Jointing is a surfacing operation in which a small

amount of wood is removed from the edges and faces

of boards to get smooth, straight and even surfaces

such that the two edges that run across the planing

blocks would fit together perfectly, forming a seamless

joint.

Planing refers to the sizing of lumber to a desired thick-

ness while creating a level surface parallel to the oppo-

site size of the board. Depth of cut is the term used to

indicate how deep the blades will cut into the workpiece.

WARNING: Operation of any power tool can result in

foreign objects being thrown into eyes which can result

in severe eye damage. Always wear safety goggles

complying with United States ANSI Z87.1 (shown on

package) before commencing power tool operation.

WARNING: For your own safety, read all of the

instructions and safety precautions before operating

tool.

• Know general power tool safety. Make sure all pre-

cautions are understood (see pages 2, 3 and 6).

• Whenever adjusting or replacing any parts on

jointer/planer, turn switch off and remove plug from

power source.

• Make sure all guards are properly attached and

securely fastened.

• Make sure all moving parts are free from interference.

• Always wear eye protection or face shield.

• Make sure blades are aligned and properly attached

to cutterhead.

• Do not plug in jointer/planer unless switch is in OFF

position. After turning switch on, allow jointer/planer

to come to full speed before operating.

• Keep hands clear of all moving parts.

• Do not force cut. Slowing or stalling will overheat

motor.

• Use quality lumber. Blades last longer and cuts are

smoother with good quality wood.

• Do not perform jointing/planing operations on materi-

al shorter than 8W', narrower than 3/4",or less than

1/4"thick

• Never make jointing cut deeper than 1/8".

• Always keep cutterhead and blade guards in proper

working condition.

• Maintain the proper relationships of infeed and out-

feed table surfaces and cutterhead blade path.

• Do not back the work toward the infeed table.

• Support the workpiece adequately at all times during

operation; maintain control of the workpiece.

• Use hold-down/push blocks for jointing material nar-

rower than 3" or planing material thinner than 3".

• Take precautions against kickback. Do not permit any-

one to stand or cross in line of cutterhead's rotation.

Kickback or thrown debris will travel in this direction.

1 2 3 4 5 6 7 8 9 10 11 ... 31 32

Comments to this Manuals

No comments

Craftsman 351.217881 Operations Instructions Page 6

Comments to this Manuals

Related products and manuals for Power tools Craftsman 351.217881