Craftsman 113.213853 Owner's Manual

SAVE THIS MANUALFOR FUTURE REFERENCEMODEL NO.113.213853DRILL PRESS WiTH1/2 HP MOTORSerialNumberModel and serial numbermay be found at the rear ofthe h

assembly7. Locate center pul ey and place in proper hole.SPINDLE PULLEY IDLER PULLEY8, Locate two (2) V-belts and choose speed for drillingoperation.

MOTOR CONNECTIONSWARNING: For your own safety, never connectplug to power source outlet until all assembly stepsare completed.1. Open motor connector

assembly1. Clean out the TAPERED HOLE in the chuck; cleanthe spindle nose with a clean cloth. Make sure thereare no foreign particles sticking to the

INSTALLING LIGHT BULB1. Install a light bulb (not larger than 60 watt) into thesocket inside the head.ADJUSTING THE TABLE SQUARE TO HEADNOTE: The comb

getting to know your drill pressFEED SPRINGADJUSTMENT3 FEEDBELT TE NSION SPRI NGLOCK7SUPPORT LOCKQUILL AND SPINDLE ASSEMBLYINSIDE OF DRILL PRESS27DRIL

This Drill Press has 12 speeds as listed below:300 RPM 1450 RPM375 RPM 1530 RPM525 RPM 2000 RPM560 RPM 2200 RPM700 RPM 3400 RPM860 RPM 4600 RPMSee rig

geffing to know your drill press26. DRILL "'ON-OFF" SWITCH... Has locking fea-ture. THIS FEATURE IS INTENDED TO HELPPREVENT UNAUTHORIZE

CHUCKKEY... It is a self-ejecting chuck key whichwill "pop" out of the chuck when you let go of it. Thisaction is designed to help prevent t

" nbasic driJmpress operatmoFollow the following instructions for operating your drill -- Neverpress to get the best results and to minimize the

2POSITIONING TABLE AND WORKPIECELock the table to the column in a position so that thetip of the drill is just a little above the top of the work-piec

FULL ONE YEAR WARRANTY OhL CRAFTSMAN DRILL PRESSIf within one year from the date of purchase, this Cra_sman Drill Press fails due to a defectin materi

basic drill press operationWARNING: TO avoid injury from spinning work ortool breakage, always clamp workpiece and back-up material securely to table

maintenanceWARNING: For your own safety, turn switch "OFF"and remove plug from power source outlet beforemaintaining or lubricating your dri

trouble shootingWARNING: For your Own safety, turn switch "OFF" and always remove plug from power source outletbefore trouble shooting.O CON

repair partsPARTS LiST FOR CRAFTSMAN 15" DRILL PRESS MODEL NO. 113.2138532311024 __25(KeyNo.12345678910111213PartNo.7138571320STD 502503713927136

repair partsPARTS LiST FOR CRAFTSMAN 15" DRILL PRESS MODEL NO. 113.213853_i_'_i_i!_;i4245SEEFIq44 46• Any attempt to repair this motor may c

11PARTS LiST FOR CRAFTSMAN 15" DRILL PRESS MODEL NO. 113.213853FIGURE 2ALWAYS ORDER BY PART NO. - NOT BY KEY NO.Key PartNo. No.1 STD 3032402 6052

PARTS LIST FOR CRA_SMAN 15"DRILL PRESS MODEL NO. 113.213853"!146Key PadNo. No.1 6050923456789FIGURE 4STD 3152357138460503STD 315255713747131

NOTES:27

SERVICEMODEL NO.113.213853DRILL PRESS WITH1/2 HP MOTORHOWTO ORDERREPAIRPARTSMOTORIZED15 INCHFLOOR MODEL DRILLPRESSNow that you have purchased your 15

21. DiRECTiON OF FEEDFeed work into a blade or cutter against the direc-tion of rotation of the blade or cutter only.22. NEVER LEAVE TOOL RUNII_,,IING

it... il"add mona!safety mnstrucuons Tot ar ! pressesc. Do not install or use any drill that exceeds 7" in 13, Think Safety. Safety is a

UNPACKING AND CHECKaNGCONTENTSTOOLS NEEDEDModel No. 113.213853 is shipped complete in one car-ton and includes a 1/2 HP 1725 RPM motor.Separate all pa

" " rmotor specifications and emectrmcaaequirementsMOTOR SPECIFICATIONS This power tool Is equipped with a 3-conductor cordThis drill press

assemblyWARNING: For your own safety, never connectplug to power source outlet until all assembly stepsare completed.ASSEMBLY OF COLUMN AND TABLE HARD

assemblyTABLELOCK2. Remove protective covering from table and discard. /Place table in table support and tighten table lock TABLE(located under table)

INSTALLING MOTOR PULLEY1. Loosen set screw in motor pulley using 1/8" HEX"L" wrench,2, Slide pulleyonto motor shaft. Line up the flat s