Craftsman 113.241680 Owner's Manual download pdf (Page 4)

N. Provide adequate support to the rear and

sides of the saw table for wider or long

work pieces.

O. Plastic and composition (like hardboard)

materials may be cut on your saw. However,

since these are usually quite hard and

slippery, the antikickback pawls may not

stop a kickback.

Therefore, be especially attentive to

following proper set-up and cutting

procedures for ripping. Do not stand, or

permit anyone else to stand, in line with a

potential kickback.

P. If you stall or jam the sawblade in the

workpiece, turn saw 'OFF", remove the

workpiece from the sawblade and check to

see if the sawblade is parallel to the miter

gauge grooves and if the spreader is in

proper alignment with the sawblade. If

ripping at the time, check to see if the rip

fence is parallel with the sawblade. Readjust

as indicated.

Q. DO NOT remove small pieces of cut-off

material that may become trapped inside the

blade guard while the saw is running. This

could endanger your hands or cause a

kickback. Turn saw "OFF" and wait until

blade stops.

R. Use extra care when ripping wood that has a

twisted grain oris twisted or bowed -- it may

rock on the table and/or pinch the sawblade.

9. KNOW YOUR CUTTING TOOLS

A. Dull, gummy, or improperlysharpened or set

cutting tools can cause material to stick,jam,

14.

15.

17.

when ripping, use the maximum diameter blade

for which the saw is designed, since under these

conditions the spreader is nearest the blade.

Adjust table inserts flush with the table top.

NEVER operate the saw unless the proper insert

is installed.

NEVER feed material into the cutting tool from

the rear of the saw. An accident and serious

injury could result.

NEVER use another person as a substitute for a

table extension, or as additional support for a

workpiece that is longer or wider than the basic

saw table, or to assist in feeding or supporting or

pulling the workpiece.

DO NOT pull the workpiece through the

sawblade - position your body at the nose (in-

feed) side of the guard: start and complete the

cut from the same side. This will require added

table support for iong or wide workpeices that

extend beyond the length or width of the saw

table.

18. THINK SAFETY.

Safety is a combination of operator common

sense and alertness at all times when the saw is

being used.

19. NOTE AND FOLLOW SAFETY iNSTRUC-

TIONS THAT APPEAR ON THE FRONT OF

YOUR SAW.

I DAi_GER I FOR YOUR OWN SAFETY:

READ AND UNDERSTAND OWNERS MANUAL BEFORE OPERATING MACHINE.

1_ WEAR SAFETY GOGGLES. S* KNOW HOW TO AVOID "KICKBACKS.'.'

2. USE SAWBLADE GUARD FOR "THRU-SAWING." 6. DO NOT PERFORM OPERATIONS "FREEHAND."

3. KEEP HANDS OUT OF PATH OF SAWBLAOE, 7. NEVER REACH AROUND OR OVER SAWBLADE.

4. USE A "PUSH-STICK" WHEN REQUIRED.

WARNING: USE 120 VOLT, |5 AMP BRANCH CIRCUIT AND USE 15 AMP, TIME DELAY FUSE,

too and machine maintenance.

NEVER ATTEMPT TO FREE A STALLED 20. WARNING: DO NOT ALLOW FAMILIARITY

SAWBLADE WITHOUT FIRST TURNING (GAINED FROM FREQUENT USE OF YOUR

THE SAW OFF. SAW) TO BECOME COMMONPLACE. -

THIS SAW. wrench to just "snug" it.

11. Crosscutting operations are more conveniently

worked and with greater safety if an auxiliary

wood facing isattached tothe mitergauge using WEAR YOUR

the holes provided. However, the facing must

not nterfere with the proper functioning of the

sawblade guard.

12.

rotates

The operation of any power tool can result in foreign

thrown i which can result

y goggles

ge)

Ltion. Safety

retail or catalog

1 2 3 4 5 6 7 8 9 ... 51 52

Comments to this Manuals

No comments

Craftsman 113.241680 Owner's Manual Page 4

Comments to this Manuals

Related products and manuals for Power tools Craftsman 113.241680