Craftsman 113.241680 Owner's Manual download pdf (Page 19)

Insert four (4) 5/16-18 x 1-1/4 in. long screws

through holes in each EXTENSION then through

table. Install flat washer, Iockwashers, and nuts on

the screws... DO NOT TIGHTEN.

Align front edge of extension with front edge of saw

table. Pull Extension UPWARDS above table

surface . .. SLIGHTLY TIGHTEN SCREWS using

1/2 in. wrench.

Using small block of hardwood and hammer, tap

extension DOWNWARDS at front, center and rear,

until it is EVEN with table surface ... TIGHTEN

SC REWS.

BLOCK OF WOOD

ALiGNiNG EXTENSIONS

Lay REAR FENCE GUIDE BAR on table to act as a

straightedge, If outer edge of extension is higher or

lower than table surface:

1. Slightly loosen nut holding the corner support

bracket to extension using 7/16 in. wrench.

2. Move end of extension up or down until outer

edge is even with table surface.., check with

GUIDE BAR... tighten nuts.

3. Recheck INNER edge of extension to make sure it

has not moved.., readjust, if necessary.

4. Adjust right extension in same manner.

CHECK AT FRONT AND

REAR OF EXTENSION

MOUNTING SWITCH

1. From among loose parts find the following:

2 Hex Head Screws, 5/16-18 x 3/4 in. long

2 F[atwashers (dia. of hole 21/64 in.)

2 External Lockwashers __

2 Hex Nuts. 5/16-18

2. Insert two 3/4 inch screws through two flat

washers then through holes in switch.

3. Insert screws through holes eight and ten in front

fence guide bar as illustrated.

4. Install two Iockwashers and nuts. Tighten nuts.

J AM NUT

5/16-18

"_ "_ ,,,7 LOCKWASHER

@-_ ,8TH HOLE

........ ---_:F \---_-_ _ FRONT FENCE

1OTH HOLE \ _ GUIDE BAR

(UPSIDE DOWN)

%%"--- WASHER

HEX HEAD SCREW

5/16-18 x 5/8 IN.

0NSTALLmNG RiP FENCE GUIDE BARS

1. From among the loose parts find the following

hardware:

2 Hex Head Screws, 5/16-18 x 1-3/4 in. long

2 Hex Head Screws, 5/16-18 x 1 in. long

4 External Lockwashers, 5/16 in.

(approx. dia. of hole 5/16 in.)

4 Hex Nuts, 5/16-18

(approx. dia. of hole 5/16 in.)

2 Spacers, 3/4 in. dia. x 1/2 in. long

2 Self-threading nuts

1 Fence Guide Bar Rod

2. Lay guide bars on saw table.

NOTE: The various holes in the bar allows them

to be positioned on this saw and also makes

them adaptable to other models.

3. Insert a 1-3/4 inch long screw through the

THIRD hole IN THE FRONT BAR as illustrated

•.. Insert another 1-3/4 inch long screwthrough

the SEVENTH hole in bar.

LEFT SIDE OF

FRONT GUIDE BAR

(GUIDE BAR IS TO BE

TTH HOLE TURNED END FOR END

3RD HOLE AFTER SCREWS ARE

"_:_ _J" _ HEX_HEAD

4. Place spacers on screws.

1 2 ... 14 15 16 17 18 19 20 21 22 23 24 ... 51 52

Comments to this Manuals

No comments

Craftsman 113.241680 Owner's Manual Page 19

Comments to this Manuals

Related products and manuals for Power tools Craftsman 113.241680

Verwandte Produkte und Handbücher für Empfänger und Verstärker Audiosource Amp Seven T