Craftsman 113.213213 Owner's Manual Page 1

Save This ManualFor Future ReferenceMODEL NO.113.213213DRILL PRESSWITHMAXIMUM DEVELOPED2 HP MOTORSerialNumberModel and serial numbermay be found at th

assembUyWARNING: For your own safety, never connect[ plug to power source outlet until all assembly_ steps are completed.- TOOLS NEEDEDMEDIUMSCREWDRIV

INSTALLATION OF TABLE/SUPPORTASSEMBLY AND HARDWARE3. Loosen set screw in column collar with 3mm HEX "L"wrench and remove collar and rack fro

6. Replace column collar (bevel side down) and posi-tion it over rack. Tighten set screw in collar with 3mrnHEX %" wrench. Rotational position of

iNSTALLiNG THE HF_ADCAUTION: To avoid back injury, get help in lift-ing the head... .L1. Remove protective bag from head assembly and dis-card. Care

MOUNTING MOTOR1. Locate four (4) 8mm Dia. x 20mm long hex head ybolts, eight (8) flat washers, and four (4) hex nutsamong loose parts.2. Put a fiat wa

5. Locate idler pulley assembly in loose parts bag and j _yplace in proper hole.IDLER PULLEY ASSEMBLYSPINDLE PULLEY6. Locate two (2) V-belts in the lo

MOTOR CONNECTIONSplug to power source outlet until ag assemblysteps are completed.1, Open motor connector box cover located on under-side of motor usi

2. Slide the chuck up over the arbor as illustrated.LL3, Unlock support lock and raise table so its about two SUPPORT(2) inches below tip of chuck. LO

iNSTALLiNG UGHT BULB1. install a light bulb (not larger than 60 watt) into thesocket insidethe head.BEVEL SCALENOTE: The bevel scale has been included

geeing to know your dritmpress3BELT TENSIONLOCK HANDLE25TABLE BEVEL LOCK27FEED SPRINGADJUSTMENT26FEED SPRING20SPRINGCAPSWITCH181BELT GUARD\2DRILLSPEED

FULL ONE YF.AR WARRANTY ON CRAFTSMAN DRILL PRESSif within one year from the date of purchase, this Craftsman Drill Press fails due to a defect inmater

This Drill Press has 12 speeds as listed below:150 RPM260 RPM300 RPM440 RPMSee inside of belt guard for specific placement of belts49(] RPM 1840 RPM o

ON-OFF SWITCHThe On-Off switch has a locking feature. This fea-ture is intended to help prevent unauthorized andpossible hazardous use by children and

DRiLLiNG TO A SPECiFiC DEPTHTo drifta BLIND hole (notall the way through)to a givendepth,proceed as follows.1. Mark the depth of the hole on the side

REMOVmNG CHUCK AND ARBORI. With the switch OFF, adjust depth scale to hold drillat a depth of (3) three inches. (See instructionsfor"Locking chuc

RE-INSTALUNG THE CHUCK AND ARBORNOTE: The chuck received with this drill press will notpermitthe use of smaller diameter drillbits. For an alter-nate

basic drill press operationFollow the following instructions for operating your drillpressto get the best results and to minimize the likeli-hood of p

iNSTALLiNG DRILL BiTS iN CHUCKWith the switch off and the key removed, insertdrill bitinto chuckfar enough to obtain maximumGRIPPING ofthe CHUCK JAWS.

T_LTING TABLE1. To use the table in a bevel (tilted) position, do the fo_-lowing:a. Using an adjustable wrench, turn the nut (on thetable lock pin) cl

adjustmentsWARNING: For your own safety turn switch"OFF" and remove plug from power source ouUetbefore making any adjustments. To avoid inju

QUILL BEARING ADJUSTMENTThe front of the head is "Split" which permits an adjust-ment to be made as the quill and the quill bearing sur-face

additionaj safety instructions for drill pressesSAFETY SIGNAL WORDS a, _f any pa_ of your driit press is missing, maifunc_DANGER: means if the s_fet,,

maintenancei WARNING: For your own safety, turn switch"OFF" and remove plug from power source outletbefore maintaining or lubricating your d

trouble shootingi ARNING: For your own safebj, turn switch "OFF" and always remove paug from power source outletbefore trouble shooting.* CO

ro293242413431 30 29PARTS UST FOR CRAFTSMAN 20" DRILL PRESSMODEL NO. 113.2132135251%,435O4946224\12282627252324/2119911810=O89FIGURE 1 PARTS LIST

G)03PARTS UST FOR CRAFTSMAN 20" DRILL PRESSMODEL NO. 113.213213Always order by Part Number -- Not by Key NumberFIGURE 1 - PARTS UST_oy! PartNo_ D

repair partsPARTS LiST FOR CRAFTSMAN 20" DRILL PRESSMODEL NO. 113.21321319I1521413l127FIGURE 2 - PARTS LIST34

repair pa sPARTS LIST FOR CRAFTSMAN 20" DRILL PRESSMODEL NO, 113,213213Always order by Part Number-Not by Key NumberFIGURE 2 - PARTS LISTKey Part

repair partsPARTS LiST FOR CRAFTSMAN 20" DRILL PRESSMODEL NO. 113.213213121112..---367Always order by Part Number-Not by Key NumberFIGURE 3 -PART

repair partsPARTS UST FOR CRAFTSMAN 20" DRILL PRESSMODEL NO. 113.213213207\9Always order by Part Number-Not by Key NumberFIGURE 4 - PARTS LISTKey

Notes38

39

10; Use only accessories designed for this driBIpress to avoid serious injury from thrown bro-ken parts or work pieces.a. When cuttinglarge diameter h

MODEL NO.113.213213DRILLPRESS WITHMAXUMUM DEVELOPED2 HP MOTORThe model number of yourdrill press is found at the rearof the head.When requesting servi

glossary of1. Workpiece 4.The item on which the cutting operations is beingperformed.2. DriU Bit or DrillThe cutting tool used in the drill press to m

motor specifications and electrical requirementsMOTOR SPECiFiCATiONSThis drill press is designed to use a 1725 RPM motoronly. Do not use any motor tha

WARNING: To avoid injury from unexpectedstarting or electrical shock, do not plug thepower cord into a source of power. This cordmust remain unplugged

List of loose parts in the box and bagsM8 x 1.25-20 LongHex head bolt (4)Clamp-column Lock (1)M5 x 0.8 - 12 LongPan head screw (1)(_ M8x16x1.6Flat was

Itlocation and function of controlsBELT TENSION LOCK HANDLES...Tighteninghandles locks motor bracket support and BELTTENSION HANDLE to maintain correc