Craftsman 358.798141-28.0cc Operator's Manual download pdf (Page 7)

IHII[II[IIIVJIJII I III I II I IIIIII I . IIII

,m,l,Wll,_llUll

A.QQi_.]Iu[IIll .V _t°°l is received assembled, repeat all steps in this'section to be sure assembly is correct

•,.v-...-...,,--.., and is adjusted for the Ol_mtor.)

iiii IIIIIIIIII ii I iiiiiiiiiiii iiiii i iii IIII i iiiiiiiiiiiiiiiii

A. PREPARATION

• This Operator's Manual has been developed to help you

assemble the tool and to provide its safe operation. It is

important that you read the entire manual to become

familiar with the tool before you begin assembly.

1. READ YOUR OPERATOR'S MANUAL

Iltli_tlltlllIII IIIIIIII Ill[ IIIH IIIIImHI i

B. ASSEMBLY STEPS

2. Tools you Will need:

a. Small Phillips Screwdriver

b. Flathead Screwdriver

c. Needle-nose Pliers

d. Tape Measure & Grease Pencil

e. Wrenches: 3/8 inch, 7/16 inch or

Adjustable wrench

" ii

IlililIliilllllI I I I I

1. SHIELD _ Figure 1

A WAR mG

Failure to install the shield in the position shown in Ytgm-e

I can result in serious injury to the operator. The shield

must be centered under the b_ housing clamp with

the widest part of the shield directed toward the engine.

_ [CAI/TION: ] The line limiter is sharp and can

Cut you.

a. Align the Stfield on the Bearing Housing with the

Shield centered under the Bearing Housing Clamp

with the widest part of the shield directed toward the

engine. Figure 1.Align screw openings.

b. Insert the four Bearing Housing Screws through the

Bearing Housing and the Shield.

c. Tighten each Screw evenly and securely with a

wrench or flathead screwdriver.

:2.TR/MMER HEAD -- Figure 2 &3

a. Remove the packing cover from the Arbor Shaft.

b. Place the Large Cup Washer on the Arbor Shaft. Fit

the center opening ofthe Washer around the shoulder

of the Dust Cup. Mal_ sure the Washer is against and

curved over the Dust Cup. Figure 2.

c. Threadthe TnmmerHeadclockwise _ ontothe

Arbor Shaft.

tL4_RDWARESHOWNACTUALSIZE

BEARING

WIDESTPART

OFSItIELD

HOUSING

i i iiii ii iiii._

d. Line up the hole in the Dust Cup with the hole in the

Bearing Housing by turning the Dust Cup. Figure 3.

e. Insert the Phillips screwdriver into the aligned holes

to keep the Arbor Shaft from turning. Figure 3.

f. Tighten the Trimmer Head against the Dust Cup

while holding the Phillips screwdriver.

g. Remove the Phillips screwdriver.

h. Press the Tap Button and pull4 inches of line from

the Trimmer Head. Figure 3. About 2 inches ofline

can be advanced each time the Tap Button is pressed.

NOTE: To remove the Trimmer Head, insert

Phillips screwdriver into the aligned holes in the Dust

Cup and the Bearing Housing. Unthread the Trim-

mer Head counterclockwiseA, m_.

Figure 3 7

1 2 3 4 5 6 7 8 9 10 11 12 ... 27 28

Comments to this Manuals

No comments

Craftsman 358.798141-28.0cc Operator's Manual Page 7

Comments to this Manuals

Related products and manuals for Power tools Craftsman 358.798141-28.0cc