Craftsman 351.227240 Specifications download pdf (Page 5)

• Install upper motor bracket under flange of vertical

motor bracket (Figure 6) and attach it using two car-

dage bolts, "/=_'fiat washers, =/_,"Iockwashers and

s/,,'-18 hex nuts.

. Attach top pahel to upper motor bracket (Figure 6)

using two carriage bolts, '¥=" fiat washers, '/,," lock-

washers and %"-18 he)( nuts.

Rgure 6 - Install Upper Motor Bracket

• Place stand upright and tighten all leg set hex nuts

with open end wrench.

ASSEMBLE MOTOR TO STAND

Refer to Figures 1 and 7, pages 3 and 5.

• Identify and locate the following parts from the hard-

ware bag:

Motor Pulley

Sl, 18 x 31,"Carriage bolt (4)

"/3="Flat washer (4)

Sl,..Lockwasher (4)

'/,.'-18 Hex nut (4)

• Identify and locate the following parts:

Motor - C

• Remove tape from motor shaft. Make sure the key

stays in the slot.

• Slide the motor pulley onto the motor shaft until flat

side of pulley hits shoulder on shaft.

NOTE: Make sure hat the hub (shoulder) on the pul-

ley Is on the outside.

• Tighte_ the two setscrews in the pulley using 3mm

hex wrench,

• Set the stand assembly on the side.

• Seat the motor on the vertical motor bracket and make

surethe slotson the motor base plate are aligned with

the slotson'the vertical motorbracket (see Figu;'_7).

Rgure 7 - Assemble Motor to Stand

• Attach motor to bracket using cardage bolts, wash_-

ers, IodoNashers and hex nuts.

NOTE: Hand tighten only.You may have to adjust motor

position later when-V=belt is installed.

• Slowly set the stand upright.

• Route the cord through the grommet in the stand

front panel.

ASSEMBLE SWlTCHBOX TO STAND

• Identifyand locate the following_ fromthe hardware

bag:

#8-32 x s/=.Pan Head Screw (2)

#8 Serrated Washer (2)

• Slide the switchboxin the slot on the front panel

• Attach switchboxto stand using the pan head

screws and serrated washers.

ASSEMBLE BED TO STAND

Refer to Figures 1 and 8, pages 3 and 5.

• Identify_ locatethe followingparts from the hardware

bag:

3/8-16x 3/,, Hex head bolt (3)

%" Lockwasher (3)

'/,-20 x '/="Pan head screw (2)

'/,"Flat washer (2)

• Identify and locate the following parts:

Handwheels-P and V-Belt-E,

WARNING: Although compact, this tool is heavy. At

least two people are required to liftthe tool.

Set the jointer bed assembly on top of the stand.

• Align the three holes in the bed with the three slots

on the stand.

• Attach the three bolts and Iockwashers and tighten.

Figure 8 - Assemble Bed to Stand

• Slip the V-belt over the drive pulley.

• Liftthe motor and slip the V-belt around the motor

pulley.

NOTE: Visually align the motor and drive pulleys and

tighten the motor mounting bolts.

• Slide the handwheel onto the elevation screw on the

infeed table and secure it using the screw and flat

washer. Repeat for attaching the handwheel to the

ouffeed table.

1 2 3 4 5 6 7 8 9 10 ... 23 24

Comments to this Manuals

No comments

Craftsman 351.227240 Specifications Page 5

Comments to this Manuals

Related products and manuals for Power tools Craftsman 351.227240