Oper_ator's _Man UalCRRFTSMRN°61/8-JOINTER/PLANERModel No.351.227240CAUTION: Read and followall Safety Rul_'sand OperatingInstructionsbefore
ADJUSTING FENCE "Refer to F'_ure 18 and 19.Jointer/planer has fence bevel stops at 90° (from bed)and 45 °. These stops are set at the factor
GaugeKnifeSpdngWedgeFigure 21 - Checking Knife Height• The pad of the gauge must be flush with the knife. Ifnot, the knife height must be adjusted. To
• Make sure that the table locks are loose.• Rnger tigMen-_ach set screw in turn, until the screw"bottoms out." "• Do not overtighten t
•"-_#_;with'thegraia-whe_ve_'i"l:;ossiblel_ ::';;:::'"::;;-:. ii:_Rotation_nRotationFigure 28 - Direction of Feed•
SYMPTOM"L.dMotor does not startMotor stalls (resulting in blownfuses or tripped circuitbreakers)Motor starts slowly or fails tocome to full speed
SYMPTOM CORRECTIVE ACTIONDepth of cut does not match 11Adjust indicator, securely tighten.depth of scale 2. See =Adjusting Knife Height," page 10
Model 351.227240 _Figure 30 Replacement Parts Illustration for Jointer/Plal,=.5452534634106 7266t7 25"_"2123 / 2122'_ "_"_ 11
KEYNO.12345678910-111213141516171819202122232425262728PART NO.2929.002930.002931.002932.002933.001395.00STD5410252934.002748.011286.002935.002941.0029
_Model 351.227240Figure 31 - Replacement Parts Illustration for Standfl ffII!I|I|!1617233212\\!422237382818
KEYNO.12345678910-111213141516171819202122PART NO.2979.002980.000615.002981.00STD5510062982.002983.002984.00STD551208STD5410082985.002986.002987.00298
Warranty... : ... 2Safety Rules... ... 2-3Unpacking.. ... 3Assembly ...
Model 351.227240Figure 32 - Replacement Parts Iliustmtion for Fence1116191520\18172225KEYNO.1234567891011121314PART NO.2964.002965.002966.00STO551031S
NOTES21
NOTES22
NOTES23
For the repair or replacement parts you needdelivered directly to your homeCall 7 am - 7 pro, 7 days a week1-800-366-PART(1-800-366-7278)Para ordenar
• Us_ recommended accessodes (refer to page 17).Use of improper accossodes may cause risk ofinjury to persons.• Handle workpiece correctly. Protect ha
- i ...WARNING: Do not attempt assembly if parts aremissing. Use this manual to order replacement parts.ASSEMBLE STANDRefer to Figures I and 2, pages
• Install upper motor bracket under flange of verticalmotor bracket (Figure 6) and attach it using two car-dage bolts, "/=_'fiat washers, =/
ASSEMBLE FENCE TO BEDRefer to Rgure 9, page 6.• Remove the two nuts and washer from the bolt onthe bottom of.fence assembly.• Carefully lift the fence
INSTALL REAR CUTTERHEAD GUARDRefer to Figures I and12, pages 3 and 7.• Identifyand locatethe followingparts from the hardwarebag:'/,-20 x 'h
WARNING: Any receptacle replacement s_uid be _performed by a qualified electrician.A temporary 3-prong to 2-prong groundingadapter (seeFigure 15) is a
Planing refersto the sizing of lumber to a desired thick-ness while creating a level surface parallel to the oppo-site size of the board. Depth of cut
Comments to this Manuals