Craftsman 351.217581 Operator's Manual download pdf (Page 4)

ATTACH DUST CHUTE

Refer to Figure 15, page 14.

Planer is best used along with a dust collector. Dust

chute is included. The dust chute (Key No. 1) is mount-

ed to the rollercase (Key No. 26) using two thumb

screws (Key No. 2). The dust chute can be mounted to

direct chips to either side of planer.

. After mounting, connect wet/dry vacuum hose to

dust chute. Be sure to turn the vacuum on before

operating the planer.

MOUNT PLANER TO WORK SURFACE

Refer to Figure 4.

° Planer is designed to be portable so it can be moved

to job site, but should be mounted to a stable, level

bench or table in a place with ample lighting and

correct power supply.

. Make sure there is plenty of room for moving the

workpiece through the entire cut. There must be

enough room that neither the operators or the

bystanders will have to stand in line with the wood

while using the tool.

. Base of planer has four mounting holes.Mount plan-

er to workbench or tool stand using bolts, flat wash-

ers and hex nuts (not supplied).

. Figure 4 shows the base dimensions, mounting

holes and required space to allow for table assembly

in horizontal position.

3/8" Dia._

°_ 145/16" --_

211/8"

20"

118/" I

24 _r ___

Figure 4 - Base Dimensions and Required Space

. Securely mount planer to work table by bolting it

through the holes. Make sure the planer does not

rock and the work table is level.

POWER SOURCE

WARNING: Do not connect planer to the power

source until all assembly steps have been completed.

The motor is designed for operation on the voltage and

frequency specified. Normal loads will be handled safely

on voltages not more than 10% above or below speci-

fied voltage. Running the unit on voltages which are not

within range may cause overheating and motor burn-

out. Heavy loads require that voltage at motor terminals

be no less than the voltage specified.

. Power supply to the motor is controlled by a switch

with key. Removing the key from switch will lock the

unit and prevent unauthorized use.

GROUNDING INSTRUCTIONS

WARNING: Improper connection of equipment

grounding conductor can result in the risk of electrical

shock. Equipment should be grounded while in use to

protect operator from electrical shock.

. Check with a qualified electrician if you do not

understand grounding instructions or if you are in

doubt as to whether the tool is properly grounded.

. This tool is equipped with an approved cord and a

3-prong grounding type plug (see Figure 5) for your

protection against shock hazards.

. Grounding plug should be plugged directly into

a properly installed and grounded 3-prong

grounding-type receptacle, as shown (see Figure 5).

Grounded Outlet =-_--__

Properly

Grounding Prong

3-Prong Plug @.__

Figure 5 - 3-Prong Receptacle

° Do not remove or alter grounding prong in any manner.

In the event of a malfunction or breakdown, grounding

provides a path of least resistance for electrical shock.

WARNING: Do not permit fingers to touch the termi-

nals of plug when installing or removing from outlet.

. Plug must be plugged into matching outlet that is

properly installed and grounded in accordance with

all local codes and ordinances. Do not modify plug

provided. If it will not fit in outlet, have proper outlet

installed by a qualified electrician.

. Inspect tool cords periodically, and if damaged, have

repaired by an authorized service facility.

° Green (or green and yellow) conductor in cord is the

grounding wire. If repair or replacement of the elec-

tric cord or plug is necessary, do not connect the

green (or green and yellow) wire to a live terminal.

. A 2-prong wall receptacle must be replaced with a

properly grounded 3-prong receptacle installed in

accordance with National Electric Code and local

codes and ordinances.

WARNING: Any receptacle replacement should be

performed by a qualified electrician.

A temporary 3-prong to 2-prong grounding adapter (see

Figure 6) is available for connecting plugs to a two pole

outlet if it is properly grounded.

Grounding Lug _ Make Sure This

Adapter Is Connected

To A Known

3-Prong Ground

2-Prong Receptacle

Figure 6 - 2-Prong Receptacle with Adapter

1 2 3 4 5 6 7 8 9 ... 27 28

Comments to this Manuals

No comments

Craftsman 351.217581 Operator's Manual Page 4

Comments to this Manuals

Related products and manuals for Power tools Craftsman 351.217581