Craftsman 113 Owner's Manual download pdf (Page 12)

ALIGNMENT

PROCEDURE

IMPORTANT:

IN ORDER

TO

OBTAIN

MAX'MUM

CUTT'NG

ACCURACY,

THE FOLLOWI'VG

S'X

STEPS

MUST

BE

CAREFULLY

FOLLOWED.

BECOME

THOROUGHLY

FAMILIAR

WITH

THESE

STEPS

SO

THAT

YOU CAN

ALWAYS

MAINTAIN

YOUR

SAW

'N

PROPER

ALIGNMENT.

THE

ACCIJRACY

OF

EACH

ADJUSTMENT

'S

ALWAYS

DEPENDENT

UPON

THE

ACCIJRACY

OF

THE

PRECEDING

ADJUSTMENT.

After

following the

6 step

assembly

and alignment

procedure

and the Basic

Saw operation

section

refer to

Trouble Shooting

section

if any difficulty

is

experienced

when

performing

any

sawing operation.

STEP

ONE

NOTE:

The

following

adjustment,

performed

properly,

will

result

in

the

work

table

being

parallel

to

the arm.

ATTACHING

AND

LEVELING

TABLE

MOUNTING

SUPPORT

CHANNELS.

1

. Attach

table

mounting

support

channels

with

four

souare

head

5/16-18

x 3/4 screws,

lockwashers

and

flat

washers and

nuts.

POSITION SCREWS

lN CENTER

OF

CHANNEL

SLOTS,

f

inger tight

to

permit

channels

to

"slip"

against

the base

when leveling.

FRO

NT

MOUNT RAILS

U5ING

I NI)E hULE)

2.

Release bevel

lock lever,

move

bevel

index

pin

to

left

and

rotate

the

motor

to

position

saw blade,

end

of

shaft

down. Lock bevel

lock.

Unlock and

hold arm

control

lever

in index

release

position

as

shown.

Position arm

against

left stop

(approximately

50o

miter). Loosen

carriage

lock

knob

and

position

carriage

directly

over left

hand

channel'

NOTE:

For

safety

reasons in

accordance

with

the

UL

standard,

stops

have

been

provided

to

prevent

3600

rotation of the

radial

arm.

Slide

the arbor

wrench

handle between

end

of

motor

shaft

and

mounting channel

to act

as a

feeler

gauge.

Carefully

lower the

motor

with elevation crank

until

the

end of shaft

is

just

touching

the

arbor

wrench. The

wrench should

slide

back and

forth with

only

slight

resistance. Tighten

screw

"A".

NOTE:

Do

not

change

this

elevation setting

until both

left

and

right

hand table support

channels

have been

ad i usted

.

4.

SQUARE

HD. SCREW

s/16-18

x

3/4

TABLE MOUNTING

SUPPORT CHANNEL

FLAT

WASHER

INDEX

RELEAsT

POSlTtO N

UNLOCK

LOCK

'i'\

5.

Move

arm

and

carriage

to

screw

"8"

and

tighten

support

in the

same

manner.

Move

arm and

carriage

to

right

hand

support

channel

and level

in

the

same

manner

you

adjusted

the

left

hand

support channel.

Recheck

both

support

channels

to

make sure

that

tightening

screws did

not affect

the accuracy

of

the

adjustment.

Elevate saw and

place

motor

in vertical

position

to

provide

clearance for

installation of

front

(work)

table.

TABLE

MOUNTING

SUPPORT CHANNEL

(LEFT

HAND)

SCREW

"8"

ARBOR

WRENCH

8.

t2

SCREW

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 43 44

Comments to this Manuals

No comments