Craftsman 54930 Owner's Manual Page 33
- Page / 76
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Remote Control
Your remote control has been programmed at the factory to
operate with your garage door opener.
Older Craftsman remote controls are NOT compatible.
Programming can be done through the learn button on the garage
door opener. To program additional accessories refer to the
instructions provided with the accessory or visit
www.craftsman.com. If your vehicle is equipped with a
Homelink
®
, you may require an external adapter depending on the
make, model, and year of your vehicle. Visit www.homelink.com
for additional information.
TO ADD, REPROGRAM, OR CHANGE A REMOTE
CONTROL/KEYLESS ENTRY PIN
1. Press and immediately release the Learn button.
2.
Remote Control: Press and hold the button on the remote
control that you wish to use.
Keyless Entry: Enter a 4-digit personal identification number
(PIN) of your choice on the keyless entry keypad. Then press
the ENTER button.
The garage door opener lights will flash (or two clicks will be
heard) when the code has been programmed. Repeat the steps for
programming additional remote controls or keyless entry devices.
“click”
“click”
1
2
LEARN LED
LEARN
Button
OR
PIN
? ? ? ?
4
GHI
5
JKL
7
P
RS
8
TUV
9
WXY
0
QZ
*
#
E
NT
E
R
0
QZ
*
#
ENTER
6
MNO
To Erase the Memory
ERASE ALL REMOTE CONTROLS AND KEYLESS ENTRIES
1. Press and hold the LEARN button on garage door opener until
the learn LED goes out (approximately 6 seconds). All remote
control and keyless entry codes are now erased. Reprogram
any accessory you wish to use.
ERASE ALL REMOTE CONTROLS, KEYLESS ENTRIES AND
SMART CONTROL DEVICES FROM GARAGE DOOR OPENER
1. Press and hold the learn button on garage door opener until
the learn LED goes out (approximately 6 seconds).
2. Immediately press and hold the learn button again until the
learn LED goes out. All codes are now erased.
Reprogram any accessory you wish to use.
33
- ENGLISH ESPAÑOL 1
- MODEL/MODELO 139.54930 1
- TABLE OF CONTENTS 2
- INTRODUCTION 2
- Unattended Operation 3
- Preparing your garage door 3
- Tools needed 3
- Planning 4
- FINISHED CEILING 5
- Support bracket 5
- See page 16 5
- Carton Inventory 6
- Motor Unit with a Light Lens 6
- Hardware Inventory 7
- INSTALLATION HARDWARE 7
- ASSEMBLY HARDWARE 7
- Bolt 1/4"-20x2-1/2" 8
- Washer 1/4" 8
- Lock Nut 1/4"-20 8
- HARDWARE SHOWN ACTUAL SIZE 8
- INCORRECT 9
- Figure 2 10
- Figure 1 10
- Figure 3 10
- INSTALLATION STEP 3 14
- RELEASED 15
- Release Arm 15
- Hang the Opener 16
- INSTALLATION STEP 5 16
- INSTALLATION STEP 6 17
- Install the Light 17
- INSTALLATION STEP 7 17
- Figure 2A 18
- Figure 2B 18
- Figure 4 18
- Figure 5 21
- INSTALLATION STEP 12 23
- Install The Protector System 23
- (Continued) 25
- Figure 10 25
- INSTALLATION STEP 13 26
- Electrical Requirements 26
- INSTALLATION STEP 14 27
- ADJUSTMENT 28
- Introduction 28
- ADJUSTMENT STEP 1 29
- Program the Travel 29
- ADJUSTMENT STEP 2 30
- ADJUSTMENT STEP 3 30
- Test The Protector System 30
- IMPORTANT SAFETY INSTRUCTIONS 31
- 16. SAVE THESE INSTRUCTIONS 31
- Features 32
- Using Your Garage Door Opener 32
- Using the Door Control 32
- Remote Control 33
- To Erase the Memory 33
- To Open the Door Manually 34
- Care of Your Opener 34
- TROUBLESHOOTING 35
- REPAIR PROTECTION AGREEMENTS 36
- REPAIR PARTS 37
- ACCESSORIES 39
- WARRANTY 39
- CONTENIDO 40
- INTRODUCCIÓN 40
- Operaciones automatizadas 41
- Herramientas necesarias 41
- Planificación 42
- Planificación (continuación) 43
- Inventario de piezas 45
- MONTAJE 46
- MONTAJE, PASO 2 46
- Instale la polea loca 47
- Instalación del cadena/cable 48
- Apretar la cadena 49
- INSTALACIÓN PASO 1 50
- INSTALACIÓN PASO 2 51
- INSTALACIÓN PASO 3 52
- Coloque el abridor 53
- INSTALACIÓN PASO 5 54
- Figura 1 54
- Figura 2 54
- Figura 3 54
- INSTALACIÓN PASO 6 55
- INSTALACIÓN PASO 7 55
- (ARRIBA) 56
- INSTALACIÓN PASO 9 58
- Figura 5 59
- Figura 6 59
- 11 mm (7 16 de pulg.) 60
- INSTALACIÓN PASO 12 61
- Instale la Protector System 62
- (continua) 62
- Figura 10 63
- CORRECTO 64
- INCORRECTO 64
- INSTALACIÓN PASO 14 65
- Introducción 66
- AJUSTES, PASO 1 67
- AJUSTES, PASO 2 68
- AJUSTES, PASO 3 68
- 16. CONSERVE ESTAS 69
- INSTRUCCIONES 69
- Funciones 70
- Control remoto 71
- Para borrar la memoria 71
- Posición con el seguro 72
- (desconexión manual) 72
- Para reconectar 72
- RESOLUCIÓN DE PROBLEMAS 73
- ACCESORIOS 75
- GARANTÍA 75
- 1-888-331-4569 76
Related products and manuals for Garage Door Opener Craftsman 54930
(96 pages)© 2020, manymanuals.com. All rights reserved. | 0.898 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals