To assembleandadjustyourtractoryouwill need:
ti _I (2) 7/16" wrenches (2) 1/2'" wrenches
(1) 3/4" wrench Tire Pressure Gauge
(1) 9/16" wrench Screwdriver
Utility Knife
NOTE: RIGHT HAND (R.H.) AND LEFT HAND (L.H.) ARE
DETERMINED FROM OPERATOR'S POSITION WHILE
SEATED ON THE TRACTOR,
WEAR EYE AND FACE SHIELD.
WASH HANDS OR CLOTHING IM-
MEDIATELY IF ACCIDENTALLY IN CON-
TACT WITH ELECTROLYTE.
DO NOT SMOKE, FUMES FROM CHARG-
ED ELECTROLYTE ARE EXPLOSIVE.
CUT AWAY VIEW
ASSEMBL Y
VENT CAP
BATTERY
TUBE
BATTERY
CELL
FIGURE I
NOTE: THIS TRACTOR IS EQUIPPED WITH AN
OPERATOR PRESENCE SENSING SWITCH. ANY AT-
TEMPT BY THE OPERATOR TO LEAVE THE SEAT WITH
THE ENGINE RUNNING AND ATTACHMENT CLUTCH
ENGAGED WILL SHUT OFF THE ENGINE°
1. Prepare Battery
READ INSTRUCTIONS INCLUDED WITH
THE BA TTERY CAPS FOUND IN BAG OF
PARTS° ALWAYS WEAR GLOVES,
CLOTHING AND GOGGLES TO PROTECT
YOUR HANDS, SKIN AND EYES.
a, Fi!l and charge battery (before instalhng) NOTE: S EE
DETAILED INSTRUCTIONS PACKAGED WiTH BAT-
TERY VENT CAPS FOUND IN BAG OF PARTS.
b Fill battery with battery acid to bottoms of tubes
in cells (Fig 1). NOTE: DO NOT OVERFILL OVER-
FILLING WILL RESULT IN DAMAGE TO TRACTOR
c, Check level of battery acid after 30 minutes. Add
additional battery acid if necessary NOTE: TIGHTEN
VENT CAPS SECURELY
d _ Charge battery at the rate of six amperes for one
hour
e o Neutralize excess battery acid for disposal by add-
ing it to four inches of water in a five gallon plastic
container Stir with a wooden or plastic paddle whde
adding baking soda until the addition of more soda
causes no more foaming
2. Instafl Seat
Seat position should be adjusted forward or back ward so that
the operator can comfortably reach Clutch/Brake Pedal and
safely operate the tractor (Fig 2)
a Place seat on seat pan. Screw he_: head machine
screw. Iockwasher and flat washer into seat (Fig 2)
Screw shoulder bolt and flat washer into ,seat (Fig 2)
Machine screw, shoulder boll and washers found in
bag of parts (shown full size on page 6)
b Tighten shoulder bolt and flat washer using a 1/2""
wrench
c Tighten he_ bolt (adjustment boll), Iockwasher and
flat washeJ using a 3/4 _" wrench
d Place seat in operatingposition Sit on the seat and
press clutch/brake pedal aH the way down if oper-
ating position is not comfortable, adjust seat
e To adjust Raise seat. Loosen adjustment bolt Sfide
seat to desired position Tighten adjustment bolt
securely
SEAT PAN
SHOULD[ ADJUSTMENT
BOLT 'BOLT
CLUTCH BRAKE PEDAL
FUEL
TANK
\
FIGURE 2
THE MACHfNE SCREW,,LOCKWASHERFLAT
WASHER ASSEMBL"t MUS"i" BE TIGHTENED
SECURELY TO PREVENT MOVEMENT OF SEAT,_
another free manual from www.searstractormanuals.com
(105 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals