Craftsman 113.232240 Specifications

f Save This Manual -_For Future ReferenceModeJ No.113,232240Jointer/Planerwith Legs and MotorSerialNumberModel and serial numbersmay be found on the b

Unpacking and Checking =Contents Ccontinued) ...List of Loose PartsBFEHM QU10

List of Loose Parts (From Bag Assembly)DRod-Knife GaugeGauge-Knife (2)Leveling Feet (4)3ram Hex-LWrenchWrench 8mm/lOmmWrench 12mm/14mmSwitch Key (t)Re

i_:¸ _ i ::i: :i • : •1WARNING: Although compact, this tool is heavy.: l:To avoid back injury, get help whenever you have: I to liftthe toolAssemble T

2. Install lower motorbrackets as shown using (4) 5/16-18carriage bolts, (4) 13/32 washers, (4) 5/16 Iockwashersand (4) 5/16-18 hex nuts attach lower

Until pulley hits shoulder on shaft. Tighten the two setscrews in:the pulley with supplied 3ram Hex "L"i wrench.i3 With the leg stand on its

Assemble Fence To Bed1. Remove the two nuts and the washer from the bolt onunderside of the fence assemMy,2, Carefully lift the fence and place it ont

Assembly (continued)Adjusting Guard Spring1. Remove the pan head screw from bottom of the guard post,2. Remove tension on.guard by turning tension kno

Getting to Know Your Jointer/Planer53 //84511WARNING: For your own safety always lock theswitch "OFF" when jointertplaner is not in use.Remo

i¸¸!:/ _ i i¸ i : . i _:!!iii!!iill_ill!i!! i _ /i!i _ ! it-----"---"-ICAUTION: Beforeturning switch "ON", make sureI theblade gua

Alignments ...Cutter Knife Alignment/AdjustmentsI WARNING: The cutter knives are extremely sharp. IDo not let your hand or finge

!:i! !ii!i i¸I!!ii/! i ill ! !HYEAR WARRANTY ON CRAFTSMAN STATIONARY TOOLie toa defect in material or workmanship within one year from the datepurchas

Alignments (continued)Cutter Knife SharpeningThe knives can be honed individually with an ordinaryoil-stone.Make sure your oilstone is not worn in the

Outfeed TableAdjustmentTo checkthis alignment proceed as follows:WARNING: To avoid injury from accidental start,made sure switch is "OFF" an

Alignments (continued)Adjusting Table Gibs"Gibs" are provided to take up all play between the mat-ing dovetail ways of the base and infeed a

Safety instructions for Basic Jointer/Planer Operation' Before Each Use:InSpect your jointer/planer.. WARNING: The 2-1/2 inch jointer/pianer pull

Safety instructions for Basic Jointer/Planer Operation (continued)- When jointing o r beveling:- Never joint or bevel workpieces less than 3/4 inchwid

Feeding the WorkplaceHold the board firmly down on both tables and againstthe f_nce. Keep fingers c_osetogelher. Feed the board ata continuous even ra

Basic Jointer/Planer Cutting Operations (continued)... ,,.,, ,==Jointing_ : : ,Joiniing is the removal of wood along the edge'of a pieceOf

Support Long WorkpiecesTo avoid injury from slips or kickbacks, use extra sup-ports (tables, saw horses, etc.) at both infeed and out-feed ends if you

Basic Jointer/Planer Cutting Operations (continued)Sliding Fence OperationWARNING: Moving parts can injure. Tu-rn jointed _ Sliding Knobplaner off and

LubricationUnplug the joint__c_start suddenly. You could be badSy hurt, jThe ball bearings inthis machine are packed with greaseat the factory, They r

Before Each UseInspect your jointer/ptaner.WARNING: The 2-1/2 inch jointer/planer pulley andthe 3-112 inch motor pulley furnished will run thecutter h

i::¸¸¸ i¸!:::://;/: :: ::::i:' Troubleshooting Guide: ::: : : ::' :1WARNING:" For your own safety turn switch "OFF" and remov

MotorNOTE: Motors used on wood working tools are particularly susceptible to the accumulation of sawdust and wood chipsand_should be blown out or &quo

Repair Parisi ,Parts List for Craftsman 6-118" Jointer/PlanerModel No. 113.232240Figure 1ii_:_••i_il;i;::,¸¸_... ;,:L7: '_i _2625313O28_ 2

Repair PartsParts List for Craftsman 6-118" Jointer/PianerMode! No, 113.232240Figure 1Always order by Part Number - Not by Key NumberKeyNo...

Repair PartsParts List for Craftsman 6-1/8" Jointer/PlanerModel No. 113.232240Figure 213128J7 910: Key Part.o.No.DescriptionI :82488_2 8248853 9*

Repair Parts ...,rll..i... rl,=Ni, ii1,1,111ii iii INParts List for Craftsman 6-1/8" Jointer/PlanerModel No. 113.232240Figure 3I271

AlwaysorderbyPartNumber- Not by Key NumberKeyNo.t234567891011121314Part No. Description824895102817824900824899824896STD541037 *STD551037i*820632-3824

Repair Parts ...! ,,i, ! , ii!1,11Parts List for Craftsman 6-118" JointedPtaner1\Model No. 113.232240Figure 4242522 212O3

iParts List for Craftsman 6-1/8" Jointer/PlanerModel No. 113.232240Figure 4Always order by Part Number - Not by Key NumberKeyNo. Part No, Descrip

Repair Parts ...Parts List for Craftsman 6-118" JointedPlanerModel No. 113.232240Figure 5161718Always order by Part Number - Not by Key Number

Safety tnstructions For Jointer/Planer (contin,Inspect your wotkpiece.• Make sure there are no nails or foreign objects in thepart of the workpiece to

iiii i,=,, iii i! i_,,11! ,, ifModel No.113.232240Jointer/Planerwith Legs and MotorThe model number of your 6-1/8Inch JointedPlaner will be foundon a

FreehandUsing the tool without holding the workpiece firmlyagainst the fence and table. This can let the workpiecetwist and kick back and must never b

Motor Speclfic.tions and Eiectr, cat Requirements (continued)i : i DANGER: To aVoid electrocution: _ ;_; I U_e only identical replacement parts when s

Changing Motor VoltageWARNING: If not properly grounded, this tool cancause an electrical shock, particularly when usedin damp locations, in proximity

Table of ContentsSafety Instructions For Jointer/Planer ... 2Safety Signal Words ... : ...

UnpackingWARNING: To avoid injury from unexpected starl-ing or electrical shock, do not plug the power cordinto a power source outlet during Unpacking