Craftsman 486.248381 User Manual download pdf (Page 8)

STEP 4: (SEE FIGURE 4)

• Assemble a shoulder bolt (P) and a 3/8" washer (X)

to the outside of R.H. side plate, securing it with a

3/8"angednut(BB).RepeatforL.H.sideplate.

FIGURE 4 RIGHT SIDE VIEW

FIGURE 3 RIGHT SIDE VIEW

5/16"

NYLOCK

NUT (CC)

5/16" x 1"

CARRIAGE BOLT (N)

ENGINE MOUNTING

PLATE

(4) 1/2" WASHERS (V)

(3) 3/8" FLANGE NUTS (BB)

(3) 3/8" x 1"

CARRIAGE

BOLTS (K)

SEE NOTE

3/8" WASHER (X)

SHOULDER

BOLT (P)

3/8" FLANGED

NUT (BB)

INSTALL SIDE PLATES

STEP 3: (SEE FIGURE 3)

• FastentheR.H.SidePlate(bendfacingout)tothe

front three holes in the tractor frame using three

3/8" x 1" carriage bolts (K), three 1/2" washers (V)

(seenote)andthree3/8"angenuts(BB). For the

rear hole, use a 5/16" x 1" carriage bolt (N), a 1/2"

washer (V) and a 5/16" nylock nut (CC). Place the 1/2"

washers (V) between the tractor frame and the side

plate. Repeat for L.H. side plate.

• Reinstallthebrowningshieldontothetractorframe

using the original screws.

NOTE: If there is an engine mounting plate (shown with

dottedlines)leavethe1/2washerofftheboltthatgoes

through the plate.

INSTALL HANGER BRACKETS AND SHOULDER

BOLTS TO OUTSIDE OF FRAME

STEP 5: (SEE FIGURE 5)

• Removethebolt,ifpresent,intheholedirectlybehind

the brake rod on the left side of the tractor frame.

• AttachtheL.H.HangerBracket(tubefacingout)tothe

hole using a 5/16" x 3/4" self threading bolt (I).

• Installaroundheadshoulderbolt(Q)intothehole

that is 9-1/2" to the rear of the bolt you just installed.

Secureitwitha3/8"angenut(BB)ontheinsideof

the frame.

FIGURE 5 LEFT SIDE VIEW

5/16" x 3/4" SELF

THREADING BOLT (I)

L.H. HANGER

BRACKET

BRAKE ROD

3/8" FLANGED

NUT (BB)

SHOULDER

BOLT (Q)

5/16" x 3/4" SELF

THREADING BOLT (I)

R.H. HANGER

BRACKET

RIGHT END OF

BRAKE ROD

3/8" FLANGED

NUT (BB)

SHOULDER

BOLT (Q)

STEP 6: (SEE FIGURE 6)

• Removethebracket,ifpresent,fromtheholedirectly

behind the end of the brake rod on the right side of

the tractor frame. Store the bracket and bolt.

• AttachtheR.H.HangerBrackettotheholeusinga

5/16" x 3/4" self threading bolt (I).

• Installaroundheadshoulderbolt(Q)intothehole

that is 9-1/2" to the rear of the bolt you just installed.

Secureitwitha3/8"angenut(BB)ontheinsideof

the frame.

FIGURE 6 RIGHT SIDE VIEW

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 39 40

Comments to this Manuals

No comments

Craftsman 486.248381 User Manual Page 8

Comments to this Manuals

Related products and manuals for Cars Craftsman 486.248381