Operator's ManualTRACTOR ATTACHMENTModel No. 486.24838142"- 2 STAGE SNOW THROWER®PRINTED IN U.S.A.FORM NO. 40242 (06/27/08) Sears, Roebuck a
10ATTACH CLUTCH IDLER ASSEMBLY TO TRACTORSTEP 12: (SEE FIGURE 12)• Attachtheclutch/idlerassemblytothetractorframe.Hook the notched suspensio
11THIS SECTION IS FOR TRACTORS WITH AN ELECTRIC ATTACHMENT CLUTCH STEP 14: (SEE FIGURE 14)• Attachthetwosuspensionarmstotherearoftheclutch
12STEP 19: (SEE FIGURE 18)• Attachtheclutch/idlerassemblytothetractorframe.Hook the notched suspension arms onto the two shoulder bolts (Q)
13STEP 22: (SEE FIGURE 21)• FastentheR.H.SidePlate(bendfacingout)tothefront three holes shown in the tractor frame using three 3/8"
14FIGURE 28 RIGHT SIDE VIEWINSTALLING HANGER BRACKETS Forbetterclearance,lowerthetractor'ssuspensionarmsusingtheattachmentliftlever.
15INSTALLING CLUTCH/IDLER ASSEMBLY ThissectioncoverstheinstallationoftheClutch/Idlerassembly to tractors with attachment clutches that are eit
16FIGURE 33 RIGHT SIDE VIEWFIGURE 32 RIGHT SIDE VIEWPIVOT LOCK PIN (MM)(use second hole)1/8" HAIRPIN COTTER (KK)ENGAGEMENTRODSTEP 33: (SEE FIG
17FIGURE 36FIGURE 38STEP 36: (SEE FIGURE 36)• Assemblethecablebrackettotheinnerhalfofthedouble holes in the bottom of the clutch/idler ass
18FIGURE 40 VIEWED FROM UNDERNEATHFIGURE 39STEP 40: (SEE FIGURE 40)• Assembletheshort"V"beltontotheenginepulleyand then onto the
19ELECTRIC ATTACHMENT CLUTCHESFIGURE 42TENSIONING CHAIN (PP)LEFT FRONT HOLEFIGURE 43 VIEW OF BOTTOM STEP 43: (SEE FIGURE 43)• Hookthespringfro
2TABLE OF CONTENTS MODEL NUMBER: 486.248381 SERIAL NUMBER: __________________ DATE OF PURCHASE: __________________The model number and seria
20FIGURE 46 VIEWED FROM UNDERNEATH1/8" HAIRPIN COTTER (KK) ENGINE PULLEY ENGINE PULLEY KEEPER BOLT IDLER PULLEY CHAIN (PP) (L.H. SIDE) STEP 47:
21STEP 48: (SEE FIGURE 47)• Placethelifthandleintotheliftbracketontherightsideof the snow thrower. Fasten the handle to the bracket usin
225/16" NYLOCK NUT (CC)CHUTE CRANKBRACKET5/16" WASHER (U)CHUTECRANKRODRODSUPPORTBRACKET5/16" x 1"CARRIAGE BOLT (N)SPIRALFIGURE 51
23NOTE:Anadditionalperson'shelpmayberequiredtomount the snow thrower to the front of the tractor.STEP 55: (SEE FIGURE 54)• Placethet
24INSTALLING THE ATTACHMENT PINSTEP 58: (REFER BACK TO FIGURE 54 ON PAGE 23)• Liftthefrontofthesnowblowertoaligntheholesinthe mounting p
25ATTACHING TO (GT) GARDEN TRACTORS WITH ASINGLE FRONT DECK SUSPENSION BRACKETSTEP 61: (SEE FIGURE 59)• Locatetheupper empty hole in the right sid
26CHECKLISTBefore you operate your snow thrower, please review the following checklist to help ensure that you will obtain the best performance from y
27OPERATIONKNOW YOUR SNOW THROWERRead this owner's manual and safety rules before operating your snow thrower.Comparetheillustrationbelowwith
28RAISING AND LOWERING• Toraise,pushdownonthelifthandleuntilthesnowthrower locks in the raised transport position.• Tolower,pushdowns
29SERVICE AND ADJUSTMENTSCAUTION: Beforeservicingoradjustingthesnowthrower,shutofftheengine,removethe spark plug wire(s), set the parkin
3SAFETYAny power equipment can cause injury if operated improperly or if the user does not understand how to operate the equipment. Exercise caution a
30PARTS TO REMOVE AT END OF SEASON• Removetheclutch/idlerassembly.(Thetwohangerbrackets and the two shoulder bolts may be left attached to the
31NOTES
32NOTES
33NOTES
34PARTSREPAIR PARTS FOR MODEL 486.248381 42" SNOW THROWER
35REPAIR PARTS FOR MODEL 486.248381 42" SNOW THROWERREF PART NO QTY DESCRIPTION 1 05931 1 Housing, Bearing 2 65701 1 Housing Assembly 3 71464 1 G
36REPAIR PARTS FOR MODEL 486.248381 42" SNOW THROWER73366076616575621165757562633233
37REF PART NO QTY DESCRIPTION1 64637 1 Lift Shaft Assembly2 710-0865 2 Hex Bolt, 1/2-13 x 1"3 710-0367 2 Hex Bolt, 5/8-11 x 1-1/2"4 711-0332
38REPAIR PARTS FOR MODEL 486.248381 42" SNOW THROWERREF PART NO QTY DESCRIPTION 1 43080 2 Carriage Bolt, 5/16-18 x 3/4" 2 43064 3 Hex Lock N
39WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face. Do not operate on slopes greater than
4GADFKLMNOSHIBBYCCCEAAPUW,XVDDQQKKREEFFIIHHGGNOT SHOWN ACTUAL SIZESHOWN ACTUAL SIZEJJJQPPLLMMOOZTNNBRRTTSSHARDWARE PACKAGE CONTENTS
® Registered Trademark / TM Trademark /SM Service Mark of Sears Brands, LLC ® Marca Registrada / TM Marca de Fábrica / SM Marca de Servicio de Sears B
5 REF. QTY. DESCRIPTION REF. QTY. DESCRIPTION X 3 Washer, 3/8" Y 2 Bowed Washer Z 6 Flanged Nut, 1/4" AA 1 Flanged Nut,
61. Cross Brace (Weight Tray)2. Side Braces (2) (Weight Tray)3. Left Hand Side Plate4. Right Hand Side Plate5. Anti-rotation Bracket6. Engagemen
7• Removeallpartsandhardwarepackagesfromthecarton. Lay out parts and hardware and identify using the illustrations on pages 4 and 6.NOTE: No
8STEP 4: (SEE FIGURE 4)• Assemble a shoulder bolt (P) and a 3/8" washer (X) to the outside of R.H. side plate, securing it with a 3/8"an
93/8" X 3-1/4" HEX BOLT (B) LARGE SPACER (SS) PULLEY (TT) 3/8" LOCKWASHER (S) 3/8" HEX LOCK NUT (DD) 3/8" WASHER (X) LONG END
Comments to this Manuals