Craftsman Dual-Stage Snow Blower Tractor Attachment Owner's Manual Page 10

  • Download
  • Add to my manuals
  • Print
  • Page
    / 36
  • Table of contents
  • TROUBLESHOOTING
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 9
10
STEP 8: (SEE FIGURE 8)
• Attachthepulley(longendofhubfacingdown)and
the3/8"spacertotheclutch/idlerassembly.Use
a3/8"x3-1/4"hexbolt,a3/8"washer,a3/8"lock
washeranda3/8"hexlocknut.
• Insertatensioningchainthroughtheholeshownand
attach the end link to the spring on the lower idler arm.
FIGURE 8
FIGURE 7
STEP 7: (SEE FIGURE 7)
• Attachthecablebrackettothedoubleholeinthe
clutch/idlerassemblyasshown,usinga5/16"x3/4"
carriageboltanda5/16"nylocknut.Placetheboltin
thefrontholeofthebracketandintheendofthehole
closest to the pulley. Do not tighten yet.
THIS SECTION IS FOR TRACTORS WITH A
MANUAL ATTACHMENT CLUTCH
If your tractor has an electric attachment clutch go to
step 14 on page 12.
FIGURE 10
HEX BOLTS
(#48138)
DRIVE BELT
FLAT IDLER
PULLEYS
STOP
Didyouselectthecorrectdrivebeltforyour
tractor?Usingthewronglengthbeltmay
causeprematurebearingorbeltfailure.
STEP 10: (SEE FIGURE 10)
• Twodifferentlengthdrivebeltsareincludedwith
your snow thrower. Tractors with manual attachment
clutchesandsinglefrontdecksuspensionbracketsuse
the56"drivebeltwith#48138 printed on the outside of
thebelt.DO NOT USEtheotherdrivebelts.
• Slightlyloosenthehexboltnexttotheatidlerpulley.
Installthedrivebeltdownbetweenthehexboltandthe
atidlerpulleywiththeatsideofthebeltagainstthe
pulley.Retightenthehexbolt.
• Loopthebeltaroundthelargev-pulley,placingit
betweenthev-pulleyandthehexboltnexttothepulley.
Placethebelttotheinsideoftheotheratidlerpulley.
5/16" x 1"
HEX BOLT
5/16" x 3/4"
HEX BOLT
5/16"
NYLOCK
5/16" WASHER
(2) 5/16"
WASHERS
FIGURE 9
STEP 9: (SEE FIGURE 9)
• Attacheachrearpulleyframebrackettotheinsideof
theclutch/idlerassemblyusingtwo5/16"x3/4"hex
bolts,5/16"washersand5/16"nylocknuts.
• Attacheachfrontpulleyframebrackettotheinside
oftheclutch/idlerassemblyusingtwo5/16"x1"hex
bolts,four5/16"washersandtwo5/16"nylocknuts.
3/8" SPACER
PULLEY
3/8" LOCKWASHER
3/8" HEX LOCK NUT
3/8"
WASHER
LONG END
OF HUB
3/8" x 3-1/4"
HEX BOLT
TENSIONING CHAIN
CABLE
BRACKET
5/16" x 3/4"
CARRIAGE BOLT
5/16" NYLOCK
NUT
Page view 9
1 ... 9 10 11 ... 36

Comments to this Manuals

No comments