Craftsman CSD40QU Owner's Manual download pdf (Page 6)

REPLACING A BIT

If the bits in the Bit Cartridge need to be

replaced, remove Bit Cartridge by pulling the

Slide button back and pushing the Bit

cartridge through the left window. Replace the

bits with the desired bits. Ensure the bits

are properly positioned in the Cartridge and

are not protruding from the back of the Bit

Cartridge. Or simply pull a worn or broken

bit from the chuck and replace it with a new

one. It will load into the Cartridge

automatically when the Slide button is

pulled back. (See Fig. 5).

NOTE:

1) Only 25 mm bits are compatible with the screwdriver.

2) If the Slide button is not pulled back fully, the Bit Cartridge will get stuck when

taking it out from the tool. Pull the Slide button all the way back.

3) The Slide button may not fully push forward if the bit cartridge is not properly

aligned inside. Make sure the bit cartridge has clicked into place when selecting

the desired bit to use. If the Slide button cannot properly be pushed forward, just

turn the bit cartridge slightly clockwise or counterclockwise and try again.

OPERATING INSTRUCTIONS cont.

(Fig. 5)

(Fig. 6A)

(Fig. 6B)

EXTENSION SHAFT

Use the extension shaft to extend the reach of the screwdriver into recessed

areas. To insert extension shaft into screwdriver, select the bit you need to

extend and push the slide button forward to engage it. Then, using your

thumb and index finger, remove the bit and insert the extension shaft into

the screwdriver. Then load the bit into the extension.

WOBBLE BIT

The wobble bit is engineered to angle into

hard to reach corners and recessed areas

by swiveling inside of the chuck

(See Fig. 6B). To use the wobble bit, first

push forward and remove one of the bits

from the Bit Cartridge. Insert the wobble

bit directly into the chuck in place of the

removed bit.

The wobble bit may also be inserted into

the end of the extension shaft to extend

the reach of the screwdriver even

further into recessed areas.

WARNING: Never change the

direction of rotation when the Chuck

is rotating; wait until it has stopped!

FORWARD / REVERSE SWITCH

(See Fig. 7)

This switch changes the chuck bit rotation

direction. Push the top of the rocker switch

for driving forward and push the bottom for

removing screws/reverse.

FORWARD

REVERSE

FORWARD

REVERSE

OPERATING INSTRUCTIONS cont.

MAINTENANCE

FULLY AUTOMATIC SPINDLE

LOCKING (AUTO-LOCK) (See Fig. 8)

The screwdriver Chuck (Fig. 8) is locked when the

On/Off Switch (Fig. 7) is not pressed. This allows

the driver to be used manually when needed.

Important: When using as a manual tool,

do not press the On/Off Switch (Fig. 7).

Otherwise the screwdriver will be damaged.

USING THE LED LIGHT (See Fig. 9)

To turn on the light simply press the On/Off

Switch. When you release the On/Off

Switch, the light will be off.

LED light increases visibility and is great

for dark or enclosed areas.

PROTECTION AGAINST DEEP

DISCHARGING

The Li-ion battery is protected against deep

discharging by the “Discharging Protection

System”. When the battery is empty, the tool

is switched off by means of a protective

circuit: The chuck no longer rotates. When

this occurs you need to recharge the battery.

Your tool requires no additional lubrication or maintenance. There are no

user serviceable parts in your power tool. Never use water or chemical

cleaners to clean your power tool. Wipe clean with a dry cloth. Always store

your power tool in a dry place. Keep the motor ventilation slots clean. Keep

all working controls free of dust. Occasionally you may see sparks through

the ventilation slots. This is normal and will not damage your power tool.

(Fig. 8)

(Fig. 9)

(Fig. 7)(Fig. 7)

1 2 3 4 5 6 7 8

Comments to this Manuals

No comments

Craftsman CSD40QU Owner's Manual Page 6

Comments to this Manuals

Related products and manuals for Power tools Craftsman CSD40QU