To inflate vehicle and bicycle tires
1. Remove 12 Volt Direct Drive Inflator from
carrying case and place evenly on flat
surface.
2. Connect the PVC coil air hose to the
Inflator by pulling back on the quick
connect coupler collar and inserting this
on valve located on the end of the 1 foot
rubber air hose. Push in firmly and pull the
quick connect coupler back until you hear
a click to lock the PVC coil in place.
3. Connect the PVC coil screw-on valve to
tire air valve by twisting clockwise until it is
securely attached to the tire air valve.
4. Connect the 12 Volt power cord into DC
12 Volt power outlet.
5. Move the On/Off switch to On position
and the Inflator will begin to operate.
Monitor the PSI on the gauge to fill your
item to desired pressure. Once you have
reached the desired air pressure, move
the On/Off switch to the Off position.
6. To remove the air hose from your tire air
valve, twist the PVC coil screw-on valve
counterclockwise.
7. Remove the 12 Volt power cord from the
DC 12 Volt power outlet.
8. Remove the PVC coil from the Inflator by
pulling back on the quick connect collar
and pulling away from the valve located
on the end of the 1 foot rubber air hose.
9. Allow unit to cool.
10. Return 12 Volt Direct Drive Inflator to the
carrying case. Store your Inflator
attachments in the carrying case.
WARNING: Risk of Flying
Objects/Bursting Objects. Over inflating
tire could cause the tire to burst or the
screw-on valve to pop off the valve stem
and become a projectile. Use a tire
pressure gauge to ensure an accurate
tire pressure reading, because the
pressure gauge on the unit is for general
reference only.
To inflate sports ball, air mattress,
rubber raft, etc.
1. Remove 12 Volt Direct Drive Inflator from
carrying case and place evenly on flat
surface.
2. Connect the PVC coil air hose to the
Inflator by pulling back on the quick
connect coupler collar and inserting this
on valve located on the end of the 1 foot
rubber air hose. Push in firmly and pull the
quick connect coupler back until you hear
a click to lock the PVC coil in place.
3. Select the appropriate inflation accessory
and screw onto end of the PVC coil
screw-on valve.
4. Connect the 12 Volt power cord into DC
12 Volt power outlet.
NOTE: For instructions on how to use
High Flow Inflator/Deflator Adaptor at
this point, see the next page.
5. Insert the inflation accessory into desired
item you are inflating.
6. Move the On/Off switch to On position and
the Inflator will begin to operate. Inflate
your desired item to the correct pressure
and move the On/Off switch to the Off
position.
7. Remove inflation accessory from PVC coil
screw-on valve.
8. Remove the 12 Volt power cord from the
DC 12 Volt power outlet.
9. Remove the PVC coil from the Inflator by
pulling back on the quick connect collar
and pulling away from the valve located
on the end of the 1 foot rubber air hose.
10. Allow unit to cool.
11. Return 12 Volt Direct Drive Inflator to the
carrying case. Store your Inflator
attachments in the carrying case.
WARNING: Risk of Bursting. Most
sports balls with no initial air will fill in
less than 10 seconds. Watch sports
balls carefully while filling, do not
overfill.
WARNING: Risk of Bursting. Too
much air pressure causes a hazardous risk
of bursting. Check the manufacturer’s
maximum pressure rating for objects being
inflated. Carefully follow Instructions.
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals