Operator's ManualCP.RFTSMRN°6 x 48" Belt, 9" DiscSANDERModel No.351.225000CAUTION: Read and followall Safety Rules and OperatingInstruc
Service RecordCraftsman 6 x 9" SanderLDATE MAINTENANCE PERFORMED REPLACEMENT PARTS REQUIRED 110
NOTES11
Models 351.225000Figure 17 - Replacement Parts Illustration for Belt Housing22\2321l 2333o \/31 2 29363 28 32 353t12
KEYNO.12345678910111213141516171819202122232425262728293O3132333435363738394OAPART NO.21425.00STD840610STD8436 I021426.0024628.00STD83302521428.002076
Models 351.225000Figure 18 - Replacement Parts Illustration for Motor and Disc713415I/1719252622202/14
KEYNO.123456789101112131415161718192O2122232425262728293031323334353637383940414243APART NO.24645.0021448.0024653.0007202.0030669.0024652.00STD8705122
LIJADORACorrea de 6 x 48", Disco de 9"Modelo No.351.225000PRECAUCION: Lea y siga todas las reglas deseguridad e instrucciones de operaci6n a
• Mantenga todas las partes listas para funcionar. Revise elprotector u otras piezas para determinar si funcionan correcta-mente y hacen el trabajo qu
• La Figura 2 muestra las dimensiones de la base, los orificiosde montaje y el espacio necesario para colocar el conjuntode la mesa y el conjunto de l
INSTRUCClONES PARA LA CONEXlON A TIERRAADVERTENClA: Si no se conecta correctamente el conductora tierra del equipo, se corre el riesgo de un electroch
Warranty ... 2Safety Rules ... 2-3Unpacking ...
Consulte las Figuras 7-16.DESCRIPClONLa Lijadora de correa y disco de Craftsman est,. construida dealuminio fundido a presi6n y hierro forjado robusto
AJUSTE DE ALINEACION DE LA CORREAConsulte la Figura 8.• Encienda y apague r_.pidamente la unidad para verificar laalineaci6n. La correa debe moverse c
Use la mesa para situar y sujetar la pieza que se est6 lijando.Mantenga el extremo topado contra la mesa y mueva la piezauniformemente a trav6s de la
• Hay correas abrasivas adicionales disponibles (v6aseAccesorios Recomendados en la p_.gina 15).• Empuje la palanca de tensidn hacia el tambor impulso
SINTOMAEl motor no arrancaEl motor no arranca; losfusibles estan quemadoso los cortacircuitos sehan disparadoEl motor no Iogradesarrollar toda supoten
NOTAS25
NOTAS26
NOTAS27
Your HomeFor expert troubleshooting and home solutions advice: aHa ewww.managemyhome.comFor repair - in your home - of all major brand appliances,lawn
• Handle the workpiece correctly. Protect hands from possi-ble injury.• Turn machine off if it jams. Belt jams when it digs toodeeply into workpiece.
B_it(B)Figure 3 - Using Table with DiscTo use the table with the belt:• Loosen bolt in pivot bracket. (see Adjusting Belt AssemblyPosition, page 6). M
A temporary 3-prong to 2-prong grounding adapter (seeFigure 6) is available for connecting plugs to a two pole outletif it is properly grounded.Ground
• Make sure abrasive belt always tracks properly. Correcttracking gives optimum performance.• After turning switch on, always allow belt and disc to c
Reposition table on support rod to ensure that gap betweentable and belt (disc) is 1/16"or less. To reposition table,loosen bolt, move table on r
• If table needs adjustment, loosen the three bolts beneathtable, move table and secure in position.Figure 13 - Table Adjustment• Use a combination sq
LUBRICATIONThe shielded ball bearings in this tool are permanentlylubricated at the factory. They require no further lubrication.• When operation seem
Comments to this Manuals