Craftsman 113.225705 Owner's Manual download pdf (Page 6)

Motor Specifications and E/ectrical Requirements (continued)

Motor Safety Protecti on

IMPORTANT: Tb avoidmotor damage; this motor should

be_blown' Out: Or vacuumed: frequently to keep sawdust

from interfering with normal motor ventilation.

1.Connect this tool to a power source with the appropri-

ate voltage for your model and a 15-amp branch circuit

with a 15-amp time delay fuse or circuit breaker. Using

the wrong size fuse can damage the motor.

2, Ifthe motor won't start, turn off the power switch imme-

d ately:and unplug the toot. Check the spindle to make

sure it turns freely. If the spindle is free, try to start the

motor again, If the motor stiU does not start, refer to the

"Motor Troubleshooting Chart.'

3. tf the motor suddenly stalls while sanding, turn off the

power switch, unplug the tool, and free the spindle

from the workpiece. The motor may now be restarted.

4. Fuses may "blow" or circuit breakers may trip fre-

quently if:

a: Motor Is Overloaded-Overloading can occur if you

sand too rapidly or make too many staWstops in a

short time.

b. Line voltages should not be more than 10% above

or below the nameplate voltage. For heavy loads,

however, the voltage at motor terminals must equal

the voltage specified for your model.

5. Most motor troubles may be traced to loose or incorrect

connections, overload, low voltage (such as small size

wire in the supply circuit) or to overly long supply circuit

wire. Always check the connections, the load and sup-

ply circuit whenever motor doesn't work well. Check

wire sizes and extension cord length with the Wire Size

Chart.

Wire Sizes

NOTE: Make sure the proper extension cord is used and

is in good condition.

The use of any extension cord will cause loss of power. To

keep this to a minimum and to prevent overheating and

motor bum-out, use the table shown to determine the min-

imum wire size (A.W.G.) extension cord.

Use only 3-wire extension cords with 3-prong grounding

type plugs and 3-pole receptacles.

Extension Wire Sizes Required

Cord Length for (A.W.G.)

t10-120V

0-25 Ft. 16

26-50 Ft. 14

Contents

Warranty ........................................................................ 2

Safety Instructions For Oscillating Spindle Sander ....... 2

Safety Signal Words. ................................................... 2

Before Using The Sander ........................................... 2

When Installing Or Moving The Sander ..................... 2

Before Each Use ........................................................ 3

PlanAhead To Protect Your Eyes, Hands, Face and Ears 3

Dress for Safety. ......................................................... 3

When Sander is Running ........................................... 4

Before Leaving The Sander ....................................... 4

Precautions To Take When Sanding Metals ................. 4

Precautions To Take When Sanding Paint .................... 4

Motor Specifications and Electrical Requirements ........ 5

General Electrical Connections .................................. 5

Power Supply and Motor Specifications ..................... 5

110-120 Volt, 60 Hz. Tool Information ........................ 5

Motor Safety Protection .............................................. 6

Wire Sizes .................................................................. 6

Contents ........................................................................ 6

Unpacking and Checking Contents ............................... 7

List of Loose Parts ....................................................... 7

Loose Parts ................................................................ 7

:i: iAssembly ..:.................................................... 8

i: i iBoiting Spindle Sander To Workbench ...................... 8

C;amping Spindle Sander To Workbench .................. 9

Mounting Spindle Sander to Legset ........................... 9

installing The ACcessory: Holder To Base .................. 9

Attaching the ACcesso_ Holder to Wa I ......... 10

.... : Changing Sleeves and [)rums .................................. 10

i i uu iii iiii i i i ul

Selection OI Spacer Ring Inserts And Upper Spindle

Washers .................................................................. 11

Getting to Know Your Spindle Sander ......................... 12

On-Off Switch ........................................................... 13

Safety Instructions for Oscillating Spindle Sander ...... 14

Before Using The Sander ......................................... 14

When Installing Or Moving The Sander ................... 14

Before Each Use ...................................................... !4

Ptan Ahead To Protect Your Eyes, Hands, Face and Ears 14

Dress for Safety ....................................................... 15

When Sander is Running ......................................... 15

Before Leaving The Sander ..................................... 15

Precautions To Take When Sanding Metals ............... 16

Precautions To Take When Sanding Paint ................. 16

Basic Sanding Operation ............................................. 16

Sanding Sleeve Selection ........................................ 16

Sanding .................................................................... 17

Feed Direction .......................................................... 17

Edge Sanding with Auxiliary Fence .......................... 17

Dust Collection Capability ........................................ 18

Transporting Sander ................................................ 18

Maintenance ................................................................ ! 8

Lubrication ................................................................ 18

Wiring Diagram ............................................................ 18

Sears Recommends The Following Accessories ........ 19

Troubleshooting ........................................................... 20

Notes ........................................................................... 21

Repair Parts ................................................................ 22

?: : !, :ii :i<i • • .......

1 2 3 4 5 6 7 8 9 10 11 ... 23 24

Comments to this Manuals

No comments

Craftsman 113.225705 Owner's Manual Page 6

Comments to this Manuals

Related products and manuals for Power tools Craftsman 113.225705