Craftsman 113.221611 Owner's Manual Page 1

Save this Manualfor Future ReferenceSears !MODEL NO,113.207600SAW ONLYMODEL NO.113.207650SAW WITH LEGSSerialNumberModel and serialnumber may be founda

assembly7 Locate table insert among loose parts and installin table by sliding the insert in place from back tofront of blade, aligning rear tab on ba

TO INSTALL/TENSION PIN TYPEBLADES:WARNING: FOR YOUR OWN SAFETY, TURNSWITCH ='OFF", REMOVE KEY AND REMOVEPLUG FROM POWER SOURCE OUTLET BEFORE

assembly3. For plain-end blades, remove blade holders (withblade installed) from retainer clips by putlingclips away from blade holders. Pull out uppe

ADJUSTING THE BLADE SQUARETO TABLEWARNING: FOR YOUR OWN SAFETY, TURNSWITCH "OFF", REMOVE KEY AND REMOVEPLUG FROM POWER SOURCE OUTLET.1, WITH

assemblyINSTALLATION OF BEVEL SCALES1 With blade installed and tensioned, Iocatetwo (2)bevel scales among loose parts2 Locate slit in paper backing on

getting to know your scrota saw13ON/OFFSWITCHITENSION KNOB 2\ GUARD LOCKKNOBS3GUARD5BLADE HOLDER4 RETAINING CLIPBLOWER 6TUBE BLADE HOLDERS7BLADE HOLDE

2 To turn machineon, placefingerunderswitchleverand pullendof switchout\3. To turn machine OFF... PUSH lever in.NEVER LEAVE THE MACHINE UNATTENDEDUNTI

basic scronHsaw operationNOTE: Make certain set screws in blade holders aretight prior to each use of the scroll sawWARNING: NEVER OPERATE WITHOUT TAB

basic scroll saw operationUSE OF MITER GAUGE -CROSS CUTTINGWARNING: TO AVOID WORK INSTABILITY ORRUNNING THE MITER GAUGE INTO THE BLADE,TURN THE MITER

MOTORFrequently vacuum or blow out any sawdust fromthe motorIf the power cord is worn, cut, or damaged in anyway, have it replaced immediatelyLUBRICAT

FULL ONE YEAR WARRANTY ON CRAFTSMAN SCROLL SAWIf within one year from the date of purchase, this Craftsman Scroll Saw fails due to a defectin material

PARTS LIST FOR CRAFTSMAN 18-INCH MOTORIZED SCROLL SAWMODEL NO. 113.207600 AND 113.2076503635755 564O414366FIGURE 12O

PARTS LIST FOR CRAFTSMAN 18-INCH MOTORIZED SCROt.L SAWMODEL NO. 113.207600 AND 113.207650Always order by Part Number - Not by Key NumberFIGURE 1%_oy P

PARTS LIST FOR CRAFTSMAN 18-INCH MOTORIZED SCROLL SAWMODEL NO. 113.207600 AND 113,2076508FIGURE 2 - MITER GAUGE ASSEMBLYKey PartNo. No. DescriptionH,

PARTS LIST FOR CRAFTSMAN 18-INCH MOTORIZED SCROLL SAWMODEL NO. 113.207600 AND 113.2076504 53| 2 '_o\6o 6 5 4_tj2 ]2FIGURE 3 - LEG SET FORMODEL 11

SERVICEMODEL NO113.207600SAW ONLYMODEL NO.113.207650SAW WITH LEGSHOW TO ORDERREPAIR PARTS18-iNCHMOTORIZED SCROLL SAWNow that you have purchased your 1

additional safety instructions for scroln sawSafety is a combination of operator common senseand alertness at all times when the scroll saw isbeing us

location and function of controlsTENSION KNOBON/OFF SWITCHGUARD LOCK KNOBS BLADE HOLDERRETAINING CLIPSGUARD BLOWERTUBE ]OLDERSBLADE HOLDERPOCKETSBEVEL

contentsPOWER TOOL WARRANTY ... 2GENERAL SAFETY INSTRUCTIONSFOR POWER TOOLS ... 2ADDITIONAL SAFETY INSTRUCTION

Item Description Qty,1 Screw, Serrated Truss Hd. 114-20 x 5/8. 242 Le ... 43 Stilfener, Side ... :i,:i,ii: 24 *Lock

MOUNTING SCROLL SAW ON LEG SET1 Place the Scroll Saw on the Steel Legs, positionas shown by aligning the mounting holes in thebase of the Scroll Saw w

assemblyMOUNTING SCROLL SAW TOMOUNTING BOARDAn alternate method of mounting is to fasten ScrollSaw to a mounting board The board should be ofsufficien

BLADE DNSTALLATUON ANDTENSIONnNG FOR PLAnN-ENDOF{ PRN TYPE BLADESNOTE: Included with the scroll saw are three 5"blades. This saw can accommodate