Craftsman 580.675611 Operator's Manual download pdf (Page 16)

StatStatienTM

The StatStationTM displays the nominal load on generator

based on output frequency, it also has a built in maintenance

reminder.

WattageMonitor Operation

The display is two seven-segment LEDsthat provide an easy-

to-read indication of the amount of power being supplied by

the generator. The load monitor displays the generator's

output as a percentage.

As generator load increases,the display values will increase.

When the displayedvalues begin flashing, the user should

stop adding electrical loads to the generator.

If the power usage becomestoo high, the letters "OL" (for

Over Load)will flash on the display. The user should reduce

the amount of load attached to the generator.

Maintenance Reminder

The LEDwill display certain codes to alert you to check oil,

change oil, check or replaceair filter and check or replace

spark plug. The following codes will display:

"C1" Check oil at 8 hour increments

"C2" Changeoil at 50 hour increments

"C3" Check or replaceair filter at 25 hour increments

"C4" Check or replacespark plug at 100 hour increments

To take advantage of the StatStation "maintenance reminder"

capabilities, the user must press the resetbutton after

completing the maintenancecalled for in the displayedcode

(Cl, C2, C3, or C4). This results in a display of "Co" or "CA",

depending on how long the button is pressed:

1) "Co" - Pressingthe reset button once quickly will display

"Co"(clearing to zero). This will clear any maintenance

codes that have elapsed up to that point and they will

begin timing again from zero.

2) "CA" - Pressing and holding the reset button for

2 seconds will display "CA"(clearing all). This clears all

maintenancecodes, even if they have not yet reached

their service point, and they will begin timing again from

ze ro.

If nominal load and maintenancecodes appear

simultaneously, the LEDshall display, alternately, the

nominal load and code as follows:

The code will display for 3 seconds, then 1/2 second off. The

load will display for 6 seconds and then 1/2 second off.

ENGINEMAIHTENANCE

WARHIHG

f'_J Unintentionalsparking can result in fire or

_¢ electric shock.

WHENADJUSTINGORMAKINGREPAIRSTOYOURGENERATOR

* Disconnectthe sparkplugwire fromtile sparkplugandplace

thewire whereit cannotcontactsparkplug.

WHENTESTINGFORENGINESPARK

* Useapprovedsparkplugtester.

* DONOTcheckfor sparkwith sparkplugremoved.

Oil

Oil Recommendations

We recommend the use of Briggs & Stratton Warranty

Certified oils for best performance. Other high-quality

detergentoils are acceptableif classified for service SF,SG,

SH,SJ or higher. DO NOTuse special additives.

Outdoor temperatures determinethe proper oil viscosity for

the engine. Usethe chart to select the best viscosity for the

outdoor temperature range expected.

104 m __

86 __

68 -- w --_

-4

-22

°C

_ m 0

L--J L--2o

;--#X_/_---30

* Below40°F(4°C)theuseof SAE30will resultinhardstarting.

** Above80°F(27°0)theuseof 10W30maycauseincreasedoil

consumption.Checkoil levelmorefrequently.

_ OTE:Synthetic oil meeting ILSACGF-2,API

certification mark and API serv,!cesymbol with

"SJ/CF ENERGYCONSERVING or higher, is an

acceptableoil at all temperatures. Use of synthetic oil

does not alter required oil change intervals.

1 2 ... 11 12 13 14 15 16 17 18 19 20 21 ... 59 60

Comments to this Manuals

No comments

Craftsman 580.675611 Operator's Manual Page 16

Comments to this Manuals

Related products and manuals for Power generators Craftsman 580.675611