Owner's ManualERRFTS],IHJI.Bench Model213 HP(Maximum Developed)5 Speeds (3[0-3600 R.P.M.)112lnch Ghuckl2.INCH DRILL PRESSModel No.137.219120CAUTI
ASSEMBLYESEWINSTRUCTIONSFor your own safety, never connect plug to power sourceoutlet until all assembly and adjustment steps arecompleted, and you ha
8.9.5.6.Sfide.the table support assembly with the rack ( 3,5)together- onto the column.Engage the bottom of the rack (5) with the lip of thecolumn sup
TNSTALLING FEED HANDLES (FlG. H)1. Locate threeieed handles in the loose parts bag'2. Screw the feed handles (1) into the threaded holes (2)in th
FENCE ASSEMBLY (Ftc. M)1 Determine the desired location for the fence (1).2. Align the mounting holes of the fence over the table' top slots.3. f
I5.To prevent personal injury afways disconnect the plug fromlhe power sourue when maklng any adjustmenls.SQUARTNGTABLETO I|EAD (FrG. O, P)NOTE: The t
QUlt-L RETURN SPRTNG {FlG. Q, R)The quill retu3n spring may need adjustment if the tensioncauses the quill to return too rapidly or too slowly.1. Lowe
lIBASIC DRILL PRESS OPERATIONSSPEEDS AND BELT PLACEMENT (Ftc. T)This drill press has 5 speeds, as listed below:540 RPM 880 RPM2610 RPM 3600 RPM1600 RP
To prevent the workpiece or backup matdrial from beingtorn from your hands while drilling, you MUST position thlworkpiece against the LEFT side of the
REMOVTNGCHUCK (FrG. Z)1. With the switch "OFF, open the jaws of the chuck aswide as possible by turning the chuck countercloclarvise.2. Tap the
POSITIONING THE TAELE ANO WORKPIECE(F|GURE.AA and BB)1. Lock the tabfe (1) to the column (2) at a position sothe tip of rhe dntt bir (3) is just above
SECTIONPAGEWarranty ...2ProductSpecifications... ...2Safetylnstructions.. ...3AccessoriesandAttachments.. ...6CartonContents ...6K
MAINTAINING YOUR DRILL PRESSFor your own safety, turn the switch OFF and remove theplugfrom the power source outlet before maintaining orlubricating y
TROUBLESHOOTING GUIDETo avoid injury from an accidental start, turn the switch OFF and always remove the plug from the power sourcebefore making any a
CRAFTSMAN 12" DRILL PRESSMODEL NO- 137.2191,20ESENIWh". servicing use only CRAFTSMAN replacement parts. Use of any other parts may create a
CRAFTSMAN 12" DRILL PRESSSGHEMATIC AMODEL NO. 137.219120"^\,26\ IKw\r-[ \-..lI,)iI/t\-'---^ 'r\JIq-./- i\-':YU\^-: ^:\n,1\U
CRAFTSMAN 12'' DRILL PRESSPARTS LIST FOR SCHEMATIC BMODEL NO. 137.219120Part No.11 1030100412 1020120113A 213713210814A 10305602A115 2701
CRAFTSMAN 12" DRILL PRESSSCHEMATIC BMODEL NO. {37.219120_/t21110w25
CRAFTSMAN 12" DRILL PRESSPARTS LIST FOR SCHEMATIC CMODEL NO. 137.219120Size ety57 2138M8L70458 2138MB170359 28078806H260 1391690561 2801A8RF0462
liloDEL NO. 137.219120(iiI- \.jT-_-696865A66'70A87./60
For repair of major brand appliances in your own.home"'no matter who made it, no matter who sold it!1'800-4-MY'HOMESM mvti*e, dav
GENERAL SAFEW INSTRUCTIONSBEFORE USING THE DRILL PRESSSafety is a combination of common sense, staying alertand knowing how to use your drill press.To
SPECIFIC SAFETY INSTRUCTIONSFOR THE"DRILL PRESSFor your own safety, do not try to use your drill pressor plug it in until it is completely assemb
GROUNDING INSTRUCTIONSIN THE EVENT OF A, MALFUNCTION OR BREAKDOWN,grounding provides a path of least resistance for electriccurrent and reduces the ri
AVAILABLEESEWIACCESSORIESUse only accessories recommended for this drill press.Follow instructions that accompany accessories. Use ofimproper accessor
It3?---=\ Az.rllt_-ffi AN ,1-S:l,,'r@ P ffi ,4#M,Fv/ts€rygggg'lcHtJKrII/f);I ANLyaeEv 8ENO:Jlf;1_atll:4P€.a-f1-r-a-E -lJ tl---Kt rl"7-
Cord clampBelttensionknobFeed springColumn collarBevel scaleSupport lock handleDepth scale stop nutsDepth scalepornlerOepth scaleFeed stop rodh stopSp
IIBASE - Supports the drill press. For additional stability,holes are provided in the base to bolt the drill press tothe floor. (See "Specific Sa
Comments to this Manuals