GARAGE DOOR OPENER1/2 HPOwner’sManualModel No.139.53662SRT2139.53670SRT1139.53675SRT2For Residential UseOnly Caution:Read and follow allsafety rules a
Assembly Step 4Install the Chain/Cable &Attach the Sprocket Cover CablePulleyCableLoopMasterLink BarMaster LinkClip-On SpringTrolleyT-railPin
• Spin the inner nut and lock washer down thethreaded shaft, away from the trolley.• To tighten the chain, turn outer nut in the directionshown. As yo
• Open your door to the highestpoint of travel as shown. Drawan intersecting horizontal lineon the header wall 2" abovethe high point. This heig
DoorHighest Pointof TravelHeaderWallPivotDistanceHeader WallHighest Pointof TravelDoorDistanceJambHardwareThe Chamberlain Group, Inc.Position Header B
Lag Screws5/16"x9x1-5/8"HighestPoint of Travel(of Garage Door)VerticalCenterLineHeaderWallGarageDoorMounting Header Bracket to WALL
HeaderBracketCablePulleyBracketTemporarySupportHeader WallGarageDoorThe Chamberlain Group, Inc.Attach Tee Rail to Header Bracket2/4/92 - 4/9/92T-railC
Installation Step 4Position the OpenerFollow instructions which apply to your doortype as illustrated.To prevent damage to steel, aluminum,fiberglass
Installation Step 5Hang the OpenerTwo representative installations are shown.Yours may be different. Hanging brackets shouldbe angled, Figure 1, to pr
Installation Step 6Install the Premium Control Console 18Do not connect to live electrical wiring. Connectonly to 24 Volt low voltage wires. Connecti
75 Watt Max.Light BulbLensGuideLensTabLensSlotLensTabLensTabInstall the lights:• Install a 75 watt maximum light bulb in eachsocket. The lights will t
Start by Reviewing these Important Safety Alert Symbols 2Contents PageA review of safety alert symbols...2You'll n
To reduce the risk of electric shock, your garagedoor opener has a grounding type plug with a thirdgrounding pin. This plug will onlyfit into a groun
The safety reversing sensor mustbe connectedand aligned correctly before the garage dooropener will move in the down direction. This is arequired safe
1/4x1-1/2"Lag Screw#10-32x3/8"Screw1/4"-20Lock Nut#10x32Lock NutStaples1/4"-20x1/2"Carriage BoltsInstallation Step 10Install
Invisible Light BeamProtection AreaSensorSensorConnect Wire toOpener TerminalsBell WireBell WireFinishedCeilingOPENER TERMINAL SCREWSSensorConnections
Installation Step 11Fasten Door Bracket Follow instructions which apply to your doortype as illustrated below or on page 25.To prevent damage to stee
Horizontal and verticalreinforcement is needed forlightweight garage doors(fiberglass, aluminum, steel, door with glass panel, etc.).Header WallVe
Ring FastenerDoorBracketClevis Pin5/16"x1-1/4"CurvedDoor ArmStraightDoor ArmClevis Pin5/16"x1"LockWashers5/16"Nuts5
Door Arm to Trolley 1 pc1/96Nuts5/16"-18LockWashers5/16"RingFastenerStraightArmScrews5/16"-18x7/8DoorBracketClevis Pin5/16&quo
Adjustment Step 1Adjust the UP and DOWN LimitsDo not make any limit adjustments until thesafety reversing sensors are completelyinstalled. 28Limit ad
Adjustment Step 2Adjust the ForceToo much force on the door will interfere withthe proper operation of the safety reversesystem. The door might not re
PliersWire CuttersClaw HammerHack SawScrewdriverAdjustable End Wrench1/2" and 7/16" Socketsand WrenchDrillTape Measure21StepladderPencil3/1
Adjustment Step 4Test the Safety Reverse SystemTest: • Place a one-inch board (or a 2x4 laid flat) on thefloor, centered under the garage door.• Oper
The remote controlThe lithium batteries shouldproduce power for up to5 years. To replace batteries,use the visor clip or screwdriverblade to pry open
To open the doormanually: The door should befully closed if possible.Pull down on the redemergency releasehandle and lift the doormanually. Torecon
33 Tornillos deajuste de límiteEtiqueta de ajustes"SRT" (learn)ButtonSECURITY✚Garage Door OpenerIndicatorLightRIGHTPANELKGKG13975139751
1. Does the opener have electric power? Plug a lamp into the outlet. If it doesn't light,check the fuse box or the circuit breaker. (Some outlet
Having a Problem? (continued)Situation Probable Cause & SolutionThe door reverses forno apparent reasonand opener lightsdon't blink:1. Is som
Repair Parts 104NOTICE89UPCEILING MOUNT ONLY1718141516131LOCKLIGHT2375651211TO GARAGE DOOR1244657RAIL GREASENO. 83A43Rail Assembly PartsInstallation
Repair PartsOpener Assembly Parts12121015161754183DNUPBrownWire(Down)ContactLIMIT SWITCHASSEMBLYGreyWireYellowWire(Up)ContactCenter LimitContactDriveG
38 Sears offers many useful accessories for your garage door opener. They are illustrated below withSears model numbers and descriptions.139.53684139
IndexAccess Door/Outside Key Release Accessory...4, 5Chain
4Safety Reversing SensorHorizontal and vertical reinforcementis needed for lightweight garage doors(fiberglass, steel, aluminum, doorwith glass pa
SEARS WARRANTYFULL 90-DAY WARRANTY ON GARAGE DOOR OPENERFor 90 days from the date of purchase, Sears will repair this Garage Door Opener, free of char
5SafetyReversing SensorClosed PositionCablePulley BracketHeaderBracketTrolleyStraightDoorArmEmergencyReleaseRope & HandleDoor BracketCurve
6 Straight DoorArm SectionCurved DoorArm SectionSafety LabelsandLiterature2-Conductor Bell WireWhite & White/RedCablePulley BracketChain
Lock Washer5/16" (4)Nut 5/16"-18 (6)Clevis Pin5/16"x2-3/4" (1)NOTICEHandleInsulatedStaples (10)Assembly HardwareInstallation H
8 Assembly Step 1Assemble the T-rail & Attach the Cable Pulley Bracket• Place the 3 T-rail sections on a flat surface forassembly. The end sectio
Assembly Step 2Install the Trolley on the T-rail• Place the opener on packing material to protectthe cover. For convenience, put a support underthe ca
Comments to this Manuals