Craftsman 390.251182 Owner's Manual

SEARSOWNER'SMANUALMODELNO.390.2511 823_90_.251982390.252282CAUTION:Read and FollowAll Safely RulesandOperating InstructionsBefore FirstUse ofThis

OPERATION MAINTENANCEPRIMING THE SHALLOW WELL PUMPTO PREVENT-DAMAGE TO INTERNAL PARTS, DO NOTSTART MOTOR UNTIL PUMP HAS BEEN FILLED WITHWATER.1. Be su

SERVICEREMOVING MOTOR FOR SERVICEAND REPLACING SHAFT SEALShould repair or replacement of motor or seal be necessary,the pump need not be disconnected

SERVICECLEANING IMPELLER1. Disassemble pump per disassembly instruction on Page10.2. Remove diffuser and impeller from pump.3. Clean impeller and reas

SYMlqOMMotor will not rtaxTROUBLESHOOTING CHART_m6sm_ causes)1.2.3.4.5.Motor runs hot and 1.overload kicks off 2.3.Motor runs but no 1.water is delive

_MLeaksat the metalclampsI _.WARNING JRelease all pressurein system beforeworking on clamp!TROUBLESHOOTING CHARTPOSSIBLE CAUSE(S) COR1RECIXV]E ACTION1

SHALLOW WELL JET AND CHECK VALVE ASSEMBLY" STOCK NO. 29650For Pump Models 390.251182, 390.251982 and 390.2522821/2/ 3/4/ 5/12To Order Parts, Call

2423132120 20A2319REPAIR PARTS45678918Figure 1411101402 11941712\,141615

KeyNO.IIIIAIBICIDIE23456789101112131415181718192020A212223241/2HPModel390.251182J218-995CwU18-1180U18-1098U18-128mC69-2U78-107PT2768L176-47PU9-399U109

REPAIR PARTSD7Single Pipe JetsSINGLE PIPE JETS6Double Pipe Jets1 2Jet No.Pkg. Max. StampedJet Pump Stock F)umping On JetSize Model No. Depth Venturi N

REPAIR PARTSVERTICAL CASING ADAPTERSiIi\ .1061723 0495To Order Parts,Call Sears Product Service,1-800-366-72782" AND 3" VERTICAL CASING ADAP

READ AND FOLLOW SAFETY INSTRUCTIONS!This is the safety alert symbol. When you see this symbolon your pump or in this manual, look for one of the fol-l

SEARSOWNER'SMANUALMODELNO.390.251182390.251 982390.252282Themodel number ofyour Deep Well Jet Pumpwill be found on the pumpbody.When requesting s

co mTs!FULL ONE YEAR WARRANTY ON CRAFTSMAN WELL PUMPSForone year from the date of purchase Sears will replace or replace this pump if defective in mat

INSTALLATION - DEEP WELL1"DISCHARGETO SERVICEPRIMING PLUG '_f PRESSURE SWITCH _FCAPTIVEAIFI_ TANK" REGULATORPLASTIC1-1/4" SUCTION

INSTALLATION - SHALLOW WELLPRIMING PLUGPRESSURE SWITCH1"DISCHARGETO SERVICESHALLOW WELL JETCHECK VALVEI-I14"END vIEW(OPTIONAL CHECKTO VALVE)

INSTALLATIONNOTICE: Use Teflon tape suppfied with the pump or Plasto-Joint Stikl for.making all pipe-thread connections to thepump itself. To avoid st

INSTALLATIONSTEEL PIPING INSTALLATIONSWhen steel pipe is-used to install the jet, be sure all pipesare clean and the ends are reamed. Screw both 1-1/4

INSTALLATION "I--IA CAUTIONINEVER run pump dry. Running pump with-out water may-overheat unit, damaging seals and possiblyburning persons handlin

ELECTRICAL_k Di_onnect power before working on pump, motor, pressure switch, or wiring.Your Motor Terminal Board (under the motor end cover)and Pressu