Craftsman 74815 - 18 Volt Cordless 12 in. Line Trimmer Operator's Manual download pdf (Page 12)

AUTOMATIC LiNE FEED SYSTEM (Fig. 15 and 16)

When turning the trimmer ON for the first time a small length of line will automatically

be fed out of the spool. To extend the line out to the full 12-inch cutting path, it will be

necessary to start the trimmer and completely stop the trimmer approximately

4 to 5 times. Each time during this operation the line will be

extended approx. ¼ to 1/2=inch(See Fig. 15). Continue _ J/_ /_q

extending the line until it comes into contact with the _\ //f _./_/

line cutter on the guard (See Fig. 16). A "clattering" \\\_\\ ._)_._--_Jj /

noise will be heard when the line hits the cutter. \ \I_\\'\ j.o/_

This is normal. The line will automatically cut. "\_/_

During use, the tip of the nylon line will become _'

frayed and worn. Cutting line will wear faster and /_'

require more feeding if the cutting, trimming and

edging is done by abrasive surfaces such as

concrete sidewalks, driveways or heavier weeds.

To feed more line, stop the trimmer completely

and restart it (4 to 5 times as explained above),

until the line comes in contact with the line

cutter on the guard.

DO NOT BUMP unit on ground in

attempt to feed line or for any

other purposes.

Fig. 15

TO MANUALLY FEEDTHE LINE (Fig. 17)

If required, line can be fed out manually. To manually feed line, press and release manual

line feed button (See Fig. 17) and gently pull out the line until line reaches the line cutter.

If the line extends past the line cutter, too much line has been fed out.

If too much line has been fed out, remove spool cap (See Page 23, Fig. 18) and with

one hand rotate the spool counterclockwise until it is stopped. Hold the spool in place,

press the manual line feed button, rotate the spool, then release the button.

The line should be shorter. Repeat these steps until the line is at the correct length,

and even with the line cutter on the guard.

Fig. 17

/K WARNING: To avoid injury, ALWAYS

remove the battery from the trimmer

BEFORE installing parts or cleaning the

trimmer or making any adjustments.

TO REPLACE CUTTING LINE (Fig. 18)

REMOVE THE SPOOL

For easy spool replacement we recommend using 71-85937, automatic feed

replacement spool and 0.065 cutting line. It is factory wound for maximum reliability.

1. Remove the battery pack from the trimmer.

2. Press the release tabs on the spool head cover and

remove cover, pulling it straight off of spool.

3. Lift the spool out of the spool housing.

REPLACE THE SPOOL

1. Replace the spool with a new factory pre-wound spool,

Craftsman 71-85937.

2. Place the replacement spool into the cut-out areas

of the spool, to line up with the one eyelet on the

spool housing. Press it down gently until you

feel it snap into place in the

spool housing.

3. Take the cutting line out of the rail

notch on the spool and feed a small length

through the eyelet (approximately 11/2inches).

4. Snap the spool head cover back on the spool

housing and at the same time make sure

that the 1 1/2inch of line is released from the

spool rail notch and is through the eyelet

and exposed outside the spool head.

The Automatic Line Feed System will advance the

line to the correct length when you operate the trimmer.

FILLING SPOOLWITH CUTTING LINE (Fig. 19)

You may wind new cutting line onto the empty spool. Only use 0.065 inch (1.65 mm)

twisted (helical or spiral) shaped, not round, line for auto feed. We recommend

Craftsman Professional 0.065-in. replacement trimmer line, Extra Quiet spiral,

in packs of 40 ft., 71-85760.

1. Remove the empty spool from the tool as described

in "TO REPLACE CUTTING LINE".

2. Remove any remaining cutting line from the spool.

3. Wind new line onto the spool; Feed 3/4 inch of

cutting line into the anchoring slot. Wind the cutting

line onto the spool in the direction of the arrow

on the spool. Make sure to wind the line neatly and

in layers. Do not crisscross (see Fig. 19).

4. When the wound cutting line reaches the recess,

cut the line. Temporarily park the line in the holding

slot on the side of the spool as shown in Fig. 19.

5. Fit the spool onto the tool as described in

"REPLACE THE SPOOL".

Fig. 19

RIGHT WRONG

1 2 ... 7 8 9 10 11 12 13 14 15 16

Comments to this Manuals

No comments

Craftsman 74815 - 18 Volt Cordless 12 in. Line Trimmer Operator's Manual Page 12

Comments to this Manuals

Related products and manuals for Power tools Craftsman 74815 - 18 Volt Cordless 12 in. Line Trimmer