Craftsman 351.219061 Operator's Manual download pdf (Page 7)

SPECIFICATIONS

Chisel capacity ........................ 1/4"to 3/4"

Maximum height of work under head,

with W' chisel and bit in place; normal

base position (not reversed): ................. 4W'

Vertical Stroke of head ..................... 45/8"

Fence to center of chisel maximum distance: ..... 3W'

Chuck capacity ............................ 3/8"

Weight ................................ 67 Ibs

OPERATION SAFETY RULES

WARNING: Operation of any power tool can result in

foreign objects being thrown into eyes which can result

in severe eye damage. Always wear safety goggles

complying with United States ANSi Z87.1 (shown on

package) before commencing power tool operation.

WARNING: For your own safety, read all of the

instructions and safety precautions before operating

tool.

• Know general power tool safety. Make sure all pre-

cautions are understood (see pages 2, 3, 5 and 6).

• Whenever adjusting or replacing any parts on mor-

riser, turn switch off and remove plug from power

source.

• Make sure all moving parts are free from interference.

• Always wear eye protection or face shield.

Do not plug in mortiser unless switch is in OFF posi-

tion. After turning switch on, allow morfiser to come

to full speed before operating.

Keep hands clear of all moving parts.

Use the mortiser only for mortising hard and soft

woods.

• Make sure workpieces are free of foreign objects

such as nails, screws, staples, etc.

Secure workpiece under holddown to prevent it from

lifting.

• Support workpiece against fence to prevent it from

spinning.

• Make sure the machine is securely mounted on its

bench, or on a plywood mounting plate that may be

clamped to a bench or other work surface.

Make sure drill bit chisel is properly secured.

Make sure drills and chisels are sharp.

Disconnect power when changing bits and chisels.

Keep lightly lubricated as directed.

• Always keep hands and fingers clear of the

descending head and the turning bit.

• Make sure all included covers are in place and

secured before operating the mortiser.

Clear blockages only after disconnecting power.

• Do not leave the morfiser running when it is unat-

tended.

• Keep children away from the mortiser at all times.

• Do not operate the mortiser when you are tired, ill or

on medications that affect your emotional or physical

stability.

Turn switch off and disconnect power whenever

mortiser is not in use.

Keep mortiser maintained. Follow maintenance

instructions (see page 9).

OPERATING THE HEAD

The head is moved with the handle. The lever is long

enough to give a great deal of leverage: make sure

the machine is clamped or bolted to the bench or

other stable surface.

Use the depth stop rod to adjust the depth of the mor-

tise. The rod has has a set screw to hold it at the depth

needed. The flat side on the depth stop rod gives good

surface for the set screw. Loosen the set screw.

Figure 15- Adjust Depth Stop

Move the chisel down to the desired depth (mark the

depth on a piece of scrap wood and bring the chisel

down to that mark).

Hold the chisel at that mark, and slide the depth stop

rod down. Tighten the set screw.

• Operate without power to check, and re-set if needed.

ADJUSTING THE FENCE

• The fence slides in and out after the knob is loos-

ened

Again use scrap stock of the correct size to align the

fence. Always check alignments before working in

good stock.

HOLD DOWN ADJUSTMENT

The hold-down keeps the workpiece from lifting as the

chisel and bit set is backed out of the mortise. Adjust

the hold-down so it just touches the top of the work-

piece, while allowing the workpiece to slide right and

left without hindrance.

Figure 16 - Adjust Hold Down

1 2 3 4 5 6 7 8 9 10 11 12 ... 19 20

Comments to this Manuals

No comments

Craftsman 351.219061 Operator's Manual Page 7

Comments to this Manuals

Related products and manuals for Power tools Craftsman 351.219061