Craftsman 113.221720 Specifications download pdf (Page 2)

WARRANTY SERVICE iS AVAILABLE BY SIMPLY"CONTACTING "irHENEAREST SEARS SERV_E

CF_NTER/DEPARTMENTTHROUGHOUT THE UN|TED STATES.

THIS WARRANTY APPUES ONLY _IILETHiS PRODUCT IS USED IN THE UNITED STATES.

This warranty gives you specific legal rights, and you may als.= have other rig hts which vary from

state to state.

SEARS, ROEBUCK ._ND CO., D/t8 WA Hoffman Estates, IL 60195

safety instructions for table saw

Safety isa combination of common sense, staying alert

and knowing how your table saw works. Read this

manual to understand this saw.

BEFORE USING THE SAW

| WARNING: To avoid roistakes that could cause I

"_serious, permanent injury, do not plug the saw in

| until the following steps have been sat|sfactorily

I completed.

1. Assembly and Alignment (See pages 9- 24).

2. Learn the use and function of the ON-OFF Switch,

Guard, Spreader,Anti-Kickback device, MiterGauge,

Fence Table Insert and Blade Elevation and Bevel

Controls. (See page 25)

3 Review and understand all safety instructions and

operating procedures inthis manual.

4. Review the maintenance methods forthis saw. (See

page 38)

Read the DANGER label found on the front ofthe saw,

as shown below.

WHEN iNSTALLiNG OR MOVING THE SAW

4. GROUND THE SAW- This saw has an approved 3-

conductor cord and a 3-pror_j grounding type plug.

The plugfits grounding type outlets designed for 120

volt 15 amp cimuits. The green conductor inthe cord

isthe grounding wire. To avoid electrocution, NEVER

connect the green wire to a live terminal.

5. To avoid injury from electrical shock, make sure your

fingers do not touch the plug's metal prongs when

pluggingin or unplugging the saw.

6. To avoid back injury get help to move the saw.

Always get help ifyou need to lift the saw. Hold the

saw close to your body. Bend your knees so you can

liftwith your legs, not your back.

7. NEVER STAND ON TOOL. Serious injury could

occur ifthe tool tipsor you accidentally hitthe cutting

tool. Do not store anything above or near the tool

where anyone might stand on the tool to reach them.

BEFORE EACH USE:

1. inspect your saw

A. To avoid injurytrom accidental starting, unplugthe

1. AVOID DANGEROUS ENVIRONMENT. Use the

saw in a dry place protected from rain. Keep work

area well lighted.

B. Support the saw so the table is level and the saw

does not rock.

C. Bolt the saw support to the floor if it tends to slip

walk, or slide during normal use.

D. When using table extensions over 24 incheswide

on any side of the saw, belt the saw supporttothe

flooror propupthe outer end of the extension from

the flcorto keep the saw fromtipping.

3. Put the saw where neither operators orbystanders

must stand in line with the saw blade.

Spreader is in linewith the sawblade,

DANGER ..... T_..... . o.o._ tl

I " set ace for hrou h cuts fence is set 2 inches or more from au_ ary f_rlce v/heR fence S set ;or D!_O p _lore

2, Wear safety goggles that m p g " _ - ' " or servi i _UL;

5 DO _ot do fre_:ha_d cuts Oracle I_etwee;_ 2 and 2 riches f o_ ad ustmg _ rig. _

AN_ Z87.t standards .... cuts _ _v ,

und or over saw 5 Kee henclsoutofpathofsaw 8. Knowhow Or_aducetheriskot bla(fe. DO not make rip --J

3. Do not reach _ro P .... OOORpM 130_, =-23_1_"

_ad_s blade, kickback. See instructlor_s for rtpp=ng, narrower than 1/2 _nch. _o v_=_= =_-._.-. ,=_ ,_ _pH

1 2 3 4 5 6 7 ... 47 48

Comments to this Manuals

No comments

Craftsman 113.221720 Specifications Page 2

Comments to this Manuals

Related products and manuals for Power tools Craftsman 113.221720