Craftsman 113.213151 Specifications

Save ThisManuam _'_For FutureReferenceMODEL NO.113.213151DRmLLPRESS WiTHMAXIMUM DEVELOPED1 HP MOTORSerialNumberModel and serial numbermay be foun

assemblyI WARNiNG: For your own safety, never connectl plug to power source outlet until all assemblyI steps are completed.- TOOLS NEEDED ...

INSTALLING THE TABLESUPPORTLOCKt. Loosen support lock and raise table support byturning table crank cRockwise until support is at aworking height leve

MOUNTING MOTOR f1 Locate four (4) 8mm Dia x 20mm long hex head j/bolts, eight (8) flat washers, and four (4) hex nutsamong loose parts. JY _'_2.

5. Locate center pulley assembly in loose parts bagand place in proper hole.SPINDLE PULLEY6. Locate two (2) V-belts in the loose parts bag,7, Use spee

MOTOR CONNECTIONSWARNING: For your own safety, never connect I' p|ug to power source outlet until aH assembJysteps are completed.1. Open motor co

\\2. Slide the chuck up over the arbor as illustrated. SPINDLECHI3. Unlock support lock and raise table so its abouttwo (2) inches below tip of chuck.

|NSTALUNG LIGHT BULBthan 60 watt) into the!ii ¸¸¸_V¸¸:: i !/ _iill i_:__ _i_I _i_i_i,_i_i,. _ _ __ _i:_i!i_i_i_ _!_ i i__ _ADJUSTING THE TABLE SQUARET

getting te know your dri_SpressFEED SPRINGADJUSTMENTFEEDSPRING17SPRINGCAPLIGHT "ON-OFF"SWITCH26DRILL SPEEDTABLE(nNSJDE BELTGUARD)1BELT GUARD

T_I_ Diili Press has t2 sp_ed_ as listed belowi : see inside of be!t guard for specific placement of belts... o_n_...,u,,,,,,D°_ 990 RPM on pulleys./

27. ORILL "ON-OFF" SWITCH ... Has Socking fea-ture, THIS FEATURE IS INTENDED TO HELPPREVENT UNAUTHORIZED AND POSSIBLEHAZARDOUS USE BY CHILD

GENERAL SAFETY iNSTRUCTiONS FOR POWER TOOLSt, KNOW YOUR POWER TOOLR_a<_ atd ur_de_st_rx, _ file tw_er,% r_anuat _uxiiabeis affixed to the _ooI. Lea

DRiLLiNG TO A SPECIFIC DEPTHTo drill a BLIND hole Inot all the way through) to agiven depth, proceed as follows.1. Mark the depth of the hole on the s

3. Turn the depth scale clockwise until it stops.4. Tighten the depth scale lock.5. The chuck will now be held at this depth when thefeed handles are

RE-INSTALLiNG THE CHUCK. AND ARBORC_ea_ the tapered surface on the arbor with a cleancloth, Make sure there are no foreign particles stiCK-_ng to the

basic pressFollow the foilowinginstruction,s foroperatng you_ drllpress toget the best _esu ts aridto Rin}r__ze t!e ikelihood of personal injury.WARNI

POSITiONiNG TABLE AND WORKPmECELock the table to the column in a position so that thetip of the drill is just a little above the top of the work-piece

TILTING TABLETo use the table in a bevel (tilted) position, loosenthe set screw under table bevel lock with a 3mmHex "L" wrench• Loosen beve

maintenanceWARNING: For your 0wn safety, turn switch 1'OFF" and remove plug from pov_er source out'_let before maintaining or lubiricat

troubWe shootingWARNING: For your own safety, turn switch "OFF" and always remove pUugfrom power source outlet-]before troubge shooting.]® C

343332313029PARTS LiST FOR CRAFTSMAN 15" DRILL PRESSMODEL NO. 113.213151.,...4945\44\394641 4347481428422526271113192416FIGURE 1 PARTS LiST

b,3¢OPARTS LiST FOR CRAFTSMAN 15" DRILL PRESSMODEL NO. 113.213151Always order by Part Number--Not by Key NumberFIGURE 1 PARTS LiSTKey PartNo No.

additional safety instructions for drim pressesWARNING: For your own safety, do not use your Idrill press unti] it is completely assembled andinstall

repmr pansi i!(PABTS LIST FOR CRAFTSMAN 15" DRILL PRESSMODEL NO. 113.213!5147/13-9Always order by Part Number-Not by Key NumberFIGURE 2 PARTS L_S

repair partsPARTS LeST FOR CRAFTSMAN 15" DRILL PRESSMODEL NO. 113.21315112J11Always order by Part Number--Not by Key NumberFIGURE 3 PARTS LISTKey

repair partsPARTS LIST FOR CRAFTSMAN 15" DRILL PRESSMODEL NO. 113.2131512o/19°_---.Always order by Part Number--Not by Key NumberFIGURE 4 PARTS L

i!iNOTES33

NOTES34

NOTESm35

ffMODEL NO.113.213151DR_LLPRESSWITHMAXaMUM DEVELOPED] HP MOTORThe model number of yourDrill Press will be found on aplate attached to the leftside of

/( i ¸¸ i! iiiiii!i!iii iii:i i!iiiiil) !i i ii ii)ii !ii ! i i , :ili i Iii!iiii i : !ii i : !ililiiii : ! i iiii i ii i:10i Use °nly access

gmessary of terms1. WorkpieceThe item on which the cutting operations is beingperformed.2. DrillThe cutting tool used in the drill press to make holes

motor specificationsand emectricamo pE nCAT O.sThis drill press is designed to use a 1725 RPM motoronly, Do not use any motor that runs faster than 17

unpacking and checking contentsWARNING: To avoid injury from unexpectedstarting or electrical shock, do not pmug thepower cord into a source of power.

A\ A,i_iii_iI'_ _ It_r_ Descr _ p_ior_ _ Oty, __ __P _A FeedHandle ::. : i.i:i:i..i... 3 _--- -- -'_B Key Drift.,. , : ; ... 1C Wrenc

ooation and function of controls1. BELTTENSION HANDLE... Turn handle counterclockwise to apply tension to belt, turn handleclockwise to release belt