Craftsman 113.213130 Owner's Manual

//_ Save This Manual "_For Future ReferenceMODEL NO.'_!3.2'13!30DRILL PRESS WITHMAXIMUM DD!ELOPED2/3 HP MOTORSerialNumberModel and seri

assembgyWARNING :FOR YOUR OWN SAFETY, NEVER CON"NECT PLUG TO POWER SOURCE OUTLET UNTILALL ASSEMBLY STEPS ARE COMPLETED.TOOLS NEEDED15/16" BO

iNSTALLiNG THE TABLESUPPORTLOCK1. Loosen support lock and raise table support byturning table crank clockwise until support is at aworking height leve

MOUNTING MOTOR1. Locate four (4) 8turn Dig × 20mrn long hex headbolts, eight (8) flat washers, and four (4) nex nutsamong loose parts.2. Install hex h

5. Locate V-belt in the loose parts bag.6. Use speed chart inside belt guard to choose speedfor drilling operation. Install belt _n correct pos_t_onfo

MOTOR CONNECTIONSWARNING: FOR YOUR OWN SAFETY- NEVER CON-NECT PLUG TO POWER SOURCE OUTLET UNTILALL ASSEt_BLY STEPS ARE COMPL ETED,WARNING; TO &VOI

_SPINDLE3. Unlock support lock and raise table so its abouttwo (2) inches below tip of chuck.4. Turn chuck sleeve clockwise and open jaws _nchuck comp

ADJUSTING THE TABLE SQUARETO HEADNOTE: The comb _t_onsauare must be "true." See'Unpacking and Checking Contents" section formethod

getting to know your driUmpressFEED SPRINGADJUSTMENTFEEDSPRING17SPRINGCAPDRILL "ON-OFF"SWITCH1BELT GUARD/2BELT TENSIONLOCK HANDLE23LOCK19 21

This Dr_ll Presshas 5 soeeds as listed below:500 R3M990 _>M1500 qPM2250 RPM3t00 RPMSee inside of belt guard for specific placement of beltson pulle

27 DRILL "ON-OFF" SWITCH . . , Has locking fea-ture. THIS FEATURE IS INTENDED TO HELPPREVENT UNAUTHORIZED AND POSSIBLEHAZARDOUS USE BY CHILD

FULL ONE YEAR WARRANTY ON CRAFTSMAN DRILL PRESSIf within one year from the date of purchase, this Craftsman Drill Press fails due to a defectin materi

i,'_i_ii_i_i_i_?, _ , i_ i i_DRILLING TO A SPECIFIC DEPTH" ttTo drill a BLIND hole (not all the way through) to a ... !igiven depth proCeed

3. Turnthedepthscaleclockwiseuntilit stops,4. Tightenthedepthscalelock.5. Thechuckwillnowbeheldatthisdepthwhenthefeedhandlesarereleased.DEPTH SCALELOC

basic d tl( press operationL;owthef0 owng nstruct ons for operating your dr -- Never do any work "FREEHAND" (hand-pres_ to get the best resu

POSITIONING "TABLE AND WORKPIECELock the table to the column in a position so that thetip of the drill is just a little above the top of the work

TILTING TABLEi: : To use the table in a bevel ttilted) position, loosen theset screw under table bevel lock with Hex "L" wrenchlLoosen bevel

maintenanceWARNING FOR YOUR OWN SAFETY, TURNSW_TCH "OFF" AND REMOVE PLUG FROM POWERSOURCE OUTLET BEFORE MAINTAINRNG OR LUB-RICATaNG YOUR DRI

trouble shootingWARNING: FOR YOUR OWN SAFETY TURN SWITCH "OFF" AND ALWAYS REMOVE PLUG FROM POWERSOURCE OUTLET BEFORE TROUBLE SHOOTING.e CONS

repair partsPARTS LmST FOR CRAFTSMAN 13" DRILL PRESSMODEL NO. 113.2131301\1656578121513Always order by Part Number--Not by Key NumberFIGURE 1 PAR

PARTS LIST FOR CRAFTSMAN 13" DRILL PRESSMODEL NO. 113.213130FIGURE 2 PARTS LIST42373634352138293033 31323\76\202122,,.,-'_(_2827268 10\ 9\\\

t4:)vPARTS LIST FOR CRAFTSMAN 13" DRILL PRESSMODEL NO. 113.213130Always order by Part Number--Not by Key NumberFIGURE 2 PARTS LISTKey I Pa_No.L_

additional safety instructions for drill pressesWARNING: FOR YOUR OWN SAFETY, DO NOTUSE YOUR DRILL PRESS UNTIL mT IS COM-PLETELY ASSEMBLED AND INSTALL

PARTS LiST FOR CRAFTSMAN 13" DRILL PRESSMODEL NO. 113.21313013Always order by Part Number--Not by Key NumberFIGURE 3 PARTS LiSTKeyNo.1I415 i6 iPa

NOTES31

SERVmCEMODEL NO.!13o2!3!30DR&L PRESS WnTHMAXIMUMDEVELOPED2/3 HP MOTORHOW TO ORDERREPAIRPARTSLLNow that you have purchased your '13-inch Drill

_:_ Dum NEVER be operated onths dd pi'e_ at a _ed g_eater than t800RPMc Do _ot inStait o_ ,,,_seany driP!that exceeds 7" inengt_ 0 e×te_tds

gaossary of terms1. WorkpieceThe item or_ which the cutti_'_g operations is beingperformed.2. DrillThe cutting tool used in the drii_ press to ma

motor specifications electricali,MOTOR SPECiFICATiONSThiS drili press is designed to use a 1725 RPM motoronly. Do not use any motor that runs faster t

unpacking and checking contentsWARNING: TO AVOID iNJURY FROM UNEX-PECTED STARTING OR ELECTRICAL SHOCK, DONOT PLUG THE POWER CORD INTO A SOURCEOF POWER

B CList of Loose Parts in Box 507872 /_'_/' _/,tern Description Qty. _LU_ \ I1_' Rod... 3 \ J I11 B Knob ...

mecation and functien ef centrols1. BELTTENSION HANDLE..• Turn handle counterclockwise to apply tension to belt. turn handleclockwise to release belt