Craftsman Garage Door Opener Owner's Manual

Garage Door OpenerOwner's ManualFOR RESIDENTIAL USE ONLYCAUTION! PLEASE READ THIS MANUAL CAREFULLYThe MODEL NUMBER label is located on the front

DO NOT WEAR WATCHES, RINGS OR LOOSE CLOTHING WHILE INSTALLING OR SERVICING A DOOR OPENER.SECTIONAL DOOR & 1-PIECE DOOR WITH TRACK1. Close door and

ONE-PIECE DOOR WITHOUT TRACKPLEASE READ AND COMPLY WITH THE WARNINGS ON PAGE 10. THEY APPLY TO THE INSTALLATION OF THEHEADER BRACKET REGARDLESS OF DOO

INSTALLATION STEP 3Position the OpenerFollow instructions which apply to your door type as illustrated.TO PREVENT DAMAGE TO LIGHT WEIGHTDOORS AND/OR D

INSTALLATION STEP 4Hang the OpenerTHE OPENER MUST BE SECURELY FASTENED TO A STRUCTURAL SUPPORT OF THE GARAGE.Three representative installations are sh

LOCATE DOOR CONTROL BUTTON (OR ANY ADDITIONAL PUSH BUTTONS) WHERE THE GARAGE DOOR IS VISIBLE,AWAY FROM DOOR AND DOOR HARDWARE AND OUT OF THE REACH OF

INSTALLATION STEP 6Install Light and LensINSTALLING LIGHT: Install a 75 watt maximum lightbulb in socket as shown. The light will turn on andremain

TO AVOID SERIOUS PERSONAL INJURYFROM ENTANGLEMENT, REMOVE ALL THEROPES CONNECTED TO GARAGE DOORBEFORE OPERATING OPENERTO AVOID DAMAGE TO GARAGE DOOR A

INSTALLATION STEP 9Fasten Door Bracket and PlateFollow instructions which apply to your door type asillustrated below.TO PREVENT DAMAGE TO LIGHTWEIGHT

INSTALLATION STEP 10Connect Door Arm to TrolleyFollow instructions which apply to your door type asillustrated.SECTIONAL DOORS ONLYMake sure garage do

ALL ONE-PIECE DOORSASSEMBLE DOOR ARM: Fasten straight and curveddoor arm sections together to their longest possiblelength. With door closed, connect

THIS SAFETY ALERT SYMBOL MEANS CAUTION—PERSONAL SAFETY OR PROPERTY DAMAGEINSTRUCTION. READ THESE INSTRUCTIONS CAREFULLY.THIS GARAGE DOOR OPENER IS DES

ADJUSTMENT STEP 1Adjust UP and DOWN LimitsLIMIT ADJUSTMENT settings regulate the points at whichthe door will stop when moving up or down.NOTE: Door

ADJUSTMENT STEP 2Adjust ForceDO NOT USE FORCE ADJUSTMENTS TOCOMPENSATE FOR A BINDING OR STICKINGGARAGE DOOR. EXCESSIVE FORCE WILLINTERFERE WITH PROPE

ADJUSTMENT STEP 3Test Safety Reverse SystemTHE SAFETY REVERSE SYSTEM TEST ISIMPORTANT. GARAGE DOOR MUSTREVERSE ON CONTACT WITH A ONE-INCH_OBSTACLE PLA

Radio ControlsF.C.C. rules prohibit adjustments to or modification of receiver and/orremote control transmitter circuitry except for changing code set

Having a Problem?Review Pages 2 and 3 Before ProceedingSITUATIONPROBABLE CAUSE & SOLUTION OPENER DOESN'T OPERATEFROM EITHER THE DOORCONT

Having a Problem? (continued)PROBABLE CAUSE & SOLUTION DOOR REVERSES FOR NO APPARENT REASON1. Pull red manual release handle. Operate door manuall

SEPARATE ALL HARDWARE FOR ASSEMBLY AND INSTALLATION PROCEDURES AS SHOWN BELOW123456710811 12 1314 151617181920212223242526

REPAIR PARTSOpener Assembly Parts List27KEYNO.PART NO. DESCRIPTION KEYNO.PART NO. DESCRIPTION1 31D380 Sprocket cover 11 41d3058 Universal replacement

Sears / CRAFTSMAN®Now that you have purchased your Sears Garage Door Opener, should aneed ever exist for repair parts or service, simply contact any S

Before you begin, please check the contents of the carton. Illustrations of parts and hardware are shown on Pages 26 and27. Separate the hardware for

BEFORE YOU BEGIN, PLEASE TAKE SOME TIME TO CAREFULLY EXAMINE THE ILLUSTRATIONS OF A TYPICAL GARAGE DOOROPENER INSTALLATION ON BOTH A SECTIONAL AND A O

Operation of Your Opener CAUTION• BEFORE YOU PROCEED, PLEASE READ SAFETY RULESON PAGE 2 AND THE OPERATING INSTRUCTIONS ONTHIS PAGE CAREFULLY• TO AVOID

CARE OF THE OPENERWhen properly installed on a door which is in balance andin good repair, opener will provide high performance with aminimum of maint

CAUTION: Do not tighten the lock nuts until boltnecks are seated in square holes and rail sectionsare positioned correctly (see right and wrong viewsb

ASSEMBLY STEP 3Fasten T-Rail to OpenerUSE ONLY THOSE SCREWS MOUNTED IN TOPOF OPENER. FAILURE TO DO SO WILL CAUSESERIOUS DAMAGE TO OPENER.CAUTION: USE

ASSEMBLY STEP 4Install Idler Pulley, Chain/ Cable& Sprocket CoverCAUTION: DO NOT REMOVE THE CHAIN/CABLE FROMTHE DISPENSER CARTON.LOCATE HARDWARE B