Craftsman 486.248462 User Manual

Owner's Manual46"- 2 STAGE SNOW THROWER TRACTOR ATTACHMENTModel No. 486.248462CAUTION:Before using this product, read this manual and follow

MOUNTING SNOW THROWER TO TRACTORASSEMBLING THE BELTSNOTE: The help of another person may be required to mount the snow thrower to the front of the tra

AUGER BELT• Make sure the auger belt is correctly assembled to the snow thrower. The belt must pass over the top of the auger pulley and then

• Loosen the two hex bolts and nuts which fasten the top of the tractor drawbar to the rear of the tractor frame. See figure 19.• Assemble the notch

OPERATIONKNOW YOUR SNOW THROWERRead this owner's manual and safety rules before operating your snow thrower.Compare the illustration below with y

HOW TO USE YOUR SNOW THROWER▲CAUTION: Never direct discharge towards bystanders or windows. Do not ailow anyone in front of unit.CONTROLLING SNOW DISC

MAINTENANCECUSTOMER RESPONSIBILITiES• Read and foilow the maintenance schedule and the maintenance procedures listed in this section.MAINTENANCE SCHED

SERVICE AND ADJUSTMENTSACAUTION: Before servicing or adjusting the snow thrower, shut off the engine, remove the spark pfug wire(s), set the parking b

STORAGE RECOMMENDATIONS• Lower the snow thrower to the ground and remove it from the tractor.• Clean the snow thrower thoroughly. Wash off any salt

REPAIR PARTS FOR MODEL 486.248462 46" SNOW THROWER106 10518

REPAIR PARTS FOR MODEL 486.248462 46" SNOW THROWERREF.NO.PARTNO.QTY. DESCRIPTIONREF.NO.PARTNO.QTY. DESCRIPTION1635761Housing Assembly58 684-00611

TABLE OF CONTENTSACCESSORIES...2SAFETY RULES...

REPAIR PARTS FOR MODEL 486.248462 46" SNOW THROWER20

REPAIR PARTS FOR MODEL 486.248462 46" SNOW THROWERREF.NO.PARTNO.QTY. DESCRIPTIONREF.NO.PARTNO.QTY. DESCRIPTION1248201Lift Bracket34 46957 1Chute

oLUPc (jiUlUC(Keep this sheet in a safe place for future reference.)Use this guide to determine if a slope is safe for the operation of your tractor a

rFor repair of major brand appliances in your own home... no matter who made it, no matter who sold it!1-800-4-MY-HOMESMAnytime, day or night(1-800-46

SAFETYAny power equipment can cause injury if operated improperiy or if the user does not understand how to operate the equipment. E

HARDWARE PACKAGE CONTENTSSHOWN ACTUAL SIZEHnTwo shear bolts (R) and hex lock nuts (S) are provided as replacement parts for the spiral augers. Store I

CARTON CONTENTSASSEMBLY1. Frame Bracket, R.H.2. Frame Bracket, L.H.3. Hanger Bracket, L.H.4. Hanger Bracket, R.H.5. Side Plate, L.H.6. Side Plat

(2) 7/16" Wrenches(2) 1/2" Wrenches(2) 9/16" Wrenches(1) 5/8" Wrench or Adjustable Wrench(1) 11/16" Wrench or Adjustable

Remove the mower stop bracket and its two boits and nuts from the R.H. side of the tractor frame as shown in figure 3.If the tractor has a muffler gua

ATTACHING CLUTCH/iDLER ASSEMBLYASSEMBLY OF SNOW THROWERIF YOUR MOWER DECK SIZE IS OTHER THAN 48"• Before attaching the clutch idler assembly to t

Remove the nylon tie which fastens the chute crank rod to the crank support tube.Assemble the crank support tube (flat side) to the two brackets on th