Craftsman Agri-Fab 50" Snow Thrower Attachment w/ Electric Lift Owner's Manual

Model No.45-04911 OWNERSMANUALPRINTED IN U.S.A. FORM NO. 41656 (08/21/14)CAUTION:Read Rules for Safe Operation and Instructions Carefully• Safety•

10STEP 12: (SEE FIGURE 10)• Attachthepulley(longendofhubfacingdown)andthe3/8"spacertotheclutch/idlerassembly.Usea3/8"x

11ATTACH CLUTCH IDLER ASSEMBLY TO TRACTORSTEP 16: (SEE FIGURE 14)• Attachtheclutch/idlerassemblytothetractorframe.Hookthenotchedrearpull

12FIGURE 185/16" x 1" HEX BOLT5/16" x 3/4"HEX BOLT5/16" NYLOCK NUT5/16" WASHER5/16"NYLOCK NUT(2) 5/16" WASHER

13STEP 22: (SEE FIGURE 20)• Attachtheclutch/idlerassemblytothetractorframe.Hookthenotchedrearpulleyframebracketsontothetwoshoulder

14STEP 24: (SEE FIGURE 22)• Removethenylontiewhichfastensthechutecrankrodtothecrankrodsupporttube.• Assemblethecrankrodsupportt

15FIGURE 25 RIGHT SIDE VIEWATTACHING SNOW THROWER TO TRACTORFIGURE 26 RIGHT SIDE VIEWSTEP 28: (SEE FIGURE 26)• Placethesnowthroweronaat,le

16FIGURE 30 VIEWED FROM UNDERNEATHINSTALLING THE AUGER BELTSTEP 32: (SEE FIGURE 30)• Startwiththesnowthrowerloweredtotheground.• Swingth

17SETTING THE AUGER BELT TENSIONSTEP 33: (SEE FIGURE 31)• Pulltherightsidetensioningchainuntiltheendofthespringispulledintothehole

18OPERATIONKNOW YOUR SNOW THROWERRead this owner's manual and safety rules before operating your snow thrower.Comparetheillustrationbelowwit

19RAISING AND LOWERING• Usethetoggleswitchattachedtothesideofthetractor'sdashtoraiseorlowerthesnowthrower.Thewinchmotorwil

2TABLE OF CONTENTSSERVICE AND ADJUSTMENTS ...20STORAGE ...

20SERVICE AND ADJUSTMENTSCAUTION: Beforeservicingoradjustingthesnowthrower,shutofftheengine,removethesparkplugwire(s),settheparkin

21PARTS TO REMOVE AT END OF SEASON• Removetheclutch/idlerassembly.(Thetwohangerbracketsandthetwoshoulderboltsmaybeleftattachedtothe

22PARTSREPAIR PARTS FOR MODEL 45-04911 50" SNOW THROWER101116171819202122454821234624254845262628293039427561414151237454856486055554040504639384

23REPAIR PARTS FOR MODEL 45-04911 50" SNOW THROWERREF PART NO QTY DESCRIPTION1 41620 1 Chute, Upper2 41621 1 Chute, Lower3 27505 1 Chute Adapt

24REPAIR PARTS FOR MODEL 45-04911 50" SNOW THROWER1223345666 666888891010101010111212131314141515161717181819192021212223242525262830313244406349

25REPAIR PARTS FOR MODEL 45-04911 50" SNOW THROWERREF PART NO QTY DESCRIPTION1 67620 1 LiftShaftAssembly2 41616 2 HexBolt,1/2-13x1"3 4

26REPAIR PARTS FOR MODEL 45-04911 50" SNOW THROWERREF PART NO QTY DESCRIPTION1 43080 1 CarriageBolt,5/16-18x3/4"2 43063 7 HexBolt,5/

27SLOPE GUIDE(Keep this sheet in a safe place for future reference.)Use this guide to determine if a slope is safe for the operation of your tractor a

the fastest way to purchase parts www.speedepart.com REPAIR PARTSAgri-Fab,Inc.809SouthHamiltonSullivan, IL. 61951217-728-8388www.agri-fab.com©201

3SAFETYReadandunderstandtheoperatinginstructionsbeforeusing.Keeptheareaofoperationclearofallpersons,especiallysmallchildrenandpets

4HARDWARE PACKAGE CONTENTSSHOWN ACTUAL SIZE43063R19171616A43768BCDIJHLK MNOF GVPTUSRQW469384284943003430704308843081476304469543082 43015 42210 47810

5IMPORTANT: Notallitemssuppliedinthehardwarebagswillbeneededforyourparticulartractor.Unneededitemsmaybediscardedafteryouhaveco

6CARTON CONTENTS1. HousingAssembly2. ChuteCrankRodAssembly3. SupportTube,CrankRod4. WinchAssembly5. Anti-rotationBracket.6. FrontPulle

7TOOLS REQUIRED FOR ASSEMBLY(2)7/16"Wrenches(2)1/2"Wrenches(2)9/16"Wrenches(2)3/4"Wrenches(1) Screw Driver(1) KnifeA

8STEP 4: (SEE FIGURE 4)• PlacetheR.H.SidePlateontotheboltsyouinsertedintothetractorframe.Installthree3/8"angedlocknutsand

9INSTALL HANGER BRACKETS AND SHOULDER BOLTS TO OUTSIDE OF FRAMESTEP 9: (SEE FIGURE 7)• Removethebolt,ifpresent,intheholedirectlybehindthe