Craftsman 315.111690 Owner's Manual Page 3

  • Download
  • Add to my manuals
  • Print
  • Page
    / 12
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 2
RULES FOR SAFE OPERATION (Continued)
21 DO NOT USE TOOL tF SWITCH DOES NOT
TURN IT ON AND OFF, Have defective switches
replaced by an authorized service center
22 DRUGS, ALCOHOL, MEDICATION. Do not
operate tool while under the influence of drugs,
alcohol, or any medication
23 DRIVING SCREWS INTO ELECTRICAL WIRING
IN WALLS, CEILINGS, OR OTHER AREAS CAN
CAUSE THE SCREWDRIVER BIT OR COLLET
TO BECOME ELECTRICALLY LIVE.Do nottouch
metal parts when driving screws into a wait; grasp
only the insulated handle(s) or plastic housing
when using this tool Make sure hidden electrical
wiring, water pipes, and mechanical hazards are
not in the path of the bit when driving screws into a
wall
INSPECT FOR and remove all nails from lumber
before driving screws
RULES FOR
24
IMPORTANT SAFETY
BATTERY TOOI.S
contact with your skin, wash immediately with
soap and water, then neutralize with lemon juice
or vinegar tf liquid gets in your eyes, flush them
with clean water for at least 10 minutes, then seek
immediate medical attention
31 If carrying your battery tool at your side, make sure
itis not running and your finger is not on lhe swilch
Avoid accidental starting
32 SECURE WORK before applying power NEVER
hold workpiece in your hand or across your legs
33 WHEN SERVICING USE ONLY IDENTICAL
CRAFTSMAN REPLACEMENT PARTS.
IMPORTANT SAFETY INSTRUCTIONS
FOR CHARGER
25 Battery tools do not have to be plugged into an
electrical outlet; therefore, they are always in
operating condition Be aware of possible hazards
when not using your battery tool or when changing
accessories
26 USE ONLY THE CHARGER PROVIDED WITH
YOUR BATTERY TOOL. Do not substitute any
other charger Use of another ct_arger could cause
batteries to explode causing possible serious injury
27 DO NOT PLACE BATTERY TOOLS OR THEIR
BATTERIES NEAR FIRE OR HEAT. They may
explode
28 DO NOT CHARGE BATTERY TOOL IN A DAMP
OR WET LOCATION°
29 Your battery tool should be charged in a location
where the temperature is mo_e than 50°F but less
than IO0°F
Jnder extreme usage or temperature conditions,
batteq, o leakage may occur If liquid comes in
34 SAVE THESE INSTRUCTIONS, This manual
contains important safety and operating
instructions for battery charger part number
999555-001
35 Before using battery charger, read atlinstructions
and cautionary markings in this manual, on battery
charger, and product using battery charger
36
, WARNING:
To reduce risk of injury, charge only nickel-
cadmium type rechargeable batteries Other
types of batteries may burst causing persona]
injury and damage
37 DO not expo"se charge'r to ;ain or snow
38 Use of an attachment not recommended or sold
by the battery charger manufacturer may resutt in
a risk of fire, electric shock, or injury to persons
39 To reduce risk of damage to charger body and
cord, pull by charger body rather than cord when
disconnecting charger
40 Make sure cord is located so that it will not be
stepped on, tripped over, or otherwise subjected
to damage or stress
WARNING:
The operation of any power tool can result in foreign objects being thrown into your eyes,
which can result in severe eye damage. Before beginning power too] operation, always wear
safety goggles or safety glasses with side shields and a full face shield when needed.. We
recommend Wide Vision Safety Mask for use over eyeglasses or standard safety glasses with
side shields, available at Sears Retail Stores.
Page 3
Page view 2
1 2 3 4 5 6 7 8 ... 11 12

Comments to this Manuals

No comments