Craftsman 19.2-volt Owner's Manual download pdf (Page 8)

8 - English

OPERATION

WARNING: Do not allow familiarity with tools to

make you careless. Remember that a careless

fraction of a second is sufficient to inflict serious

injury.

WARNING: Always wear eye protection with side

shields marked to comply with ANSI Z87.1. Failure to

do so could result in objects being thrown into your

eyes resulting in possible serious injury.

WARNING: Do not use any attachments or acces-

sories not recommended by the manufacturer of

this tool. The use of attachments or accessories not

recommended can result in serious personal injury.

APPLICATIONS

You may use this tool for the purposes listed below:

 Driving long deck screws while building a deck

 Driving carriage bolts into deck posts

 Driving masonry screws into block walls and concrete

 Driving screws into metal studs

 Driving nuts and bolts using an impact socket

This product will accept Craftsman

® 19.2 V lithium-ion bat-

tery packs and Craftsman 19.2 V nickel-cadmium battery

packs.

For complete charging instructions, refer to the Opera-

tor’s Manual for your Craftsman battery pack and charger

models.

BATTERY PROTECTION FEATURES

Craftsman 19.2 V lithium-ion batteries are designed with

features that protect the lithium-ion cells and maximize

battery life. Under some operating conditions, these built-

in features may cause the battery and the tool it is power-

ing to act

differently from nickel-cadmium batteries.

During some applications, the battery electronics may

signal the battery to shut down, and cause the tool to stop

running. To reset the battery and tool, release the trigger

and resume normal operation.

NOTE: To prevent further shut down of the battery, avoid

forcing the tool.

If releasing the trigger does not reset the battery and

tool, the battery pack is depleted. If depleted, the battery

pack will begin charging when placed on the lithium-ion

charger.

C3 ENERGY INDICATOR WINDOW

See Figure 1, page i.

The C3 energy indicator window located on the side of the

handle, just above the base, will light when the 113710

Craftsman 19.2 V lithium-ion battery pack is installed and

has charge.

NOTE: Feature will not light with Craftsman 19.2 V nickel-

cadmium battery packs.

SWITCH TRIGGER

See Figure 2, page i.

To turn the driver ON, depress the switch trigger. To turn it

OFF, release the switch trigger.

VARIABLE SPEED

See Figure 2, page i.

This tool has a variable speed switch that delivers higher

speed with increased trigger pressure. Speed is controlled

by the amount of switch trigger depression.

NOTE: You might hear a whistling or ringing noise from

the switch during use. Do not be concerned; this is a

normal part of the switch function.

DIRECTION OF ROTATION SELECTOR

(FORWARD/REVERSE/CENTER LOCK)

See Figure 2, page i.

The direction of bit rotation is reversible and is controlled

by a selector located above the switch trigger. With the

impact driver held in normal operating position, the direc-

tion of rotation selector should be positioned to the left

of the switch trigger for driving. The driving direction is

reversed when the selector is to the right of the switch

trigger.

Setting the direction of rotation selector in the OFF (center

lock) position helps reduce the possibility of accidental

starting when not in use.

NOTICE: To prevent gear damage, always al-

low the coupler to come to a complete stop before

changing the direction of rotation.

To stop the impact driver, release the switch trigger and

allow the coupler to come to a complete stop.

NOTE: The impact driver will not run unless the direction

of rotation selector is pushed fully to the left or right.

Avoid running the driver at low speeds for extended periods

of time. Running at low speeds under constant usage may

cause the driver to become overheated. If this occurs, cool

the driver by running it without a load and at full speed.

INSTALLING/REMOVING BATTERY PACK

See Figure 3, page i.

To install the battery pack:

 Lock the switch trigger by placing the direction of

rotation (forward/reverse/center lock) selector in center

position.

 Align raised rib on battery pack with the groove inside

the impact driver.

 Make sure the latches on each side of the battery pack

snap in place and battery pack is secured before be-

ginning operation.

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 19 20

Comments to this Manuals

No comments

Craftsman 19.2-volt Owner's Manual Page 8

Comments to this Manuals

Related products and manuals for Power impact wrenches Craftsman 19.2-volt