Tbe spinnaker halyard is lead over lhe forward sheave in lhemast head.e)The jib halyard is ted over the sheave in the forward face
f)Replicate the same operations in a) on the running backstaysand check stars. Remove and replace the stainless cover platefor inst
Rig the spinnaker sheet to the clcoutboard spinnaker pole fitting.Ised loop on the underside of theSee Photo.ef)Shackle the jib halya
2.4.1.5 TUNING THE RJGThe rigging needs to be tensioned beiproperly support the mast before goilfollowing procedure.are sailing.19 saili
RIGGING THE RUNNING RIGGING2.4.1.7The running rigging components are individually labeled and shouldconsist of the following:1 Each1 E
g)The boom vang is a 2: 1 tack1eThis yie1ds a 12:1 total purchasevang and the trip1e block withplate on the aft face of the ma:w
This completes the running rigging inhalyard tails are stowed in the cabin.is designed to allow clearance for thestallation. Please
*Safety equipment:ring buoy:5. etc.)ired in your area.PFD's (life preservers)Throwable horseshoe orHornShip's bellEmergency signal
s to the art port and starboardt be attached to the heavy guagett lines are necessary because the, with respect to the center pick
(~.3.1.(
Dear Owner,Welcome aboard your new 11 :METRE One Design.manual helpful and informative.We hope you will find thisYour decision to own
Prepare yourself for any situatiol1Follow the instructions providelmanual, and all applicableregulations.b)l before going out on the w
Hammers -large and smallwith marlinspikeScrewdrivers -Iarge and smalI. standard and phillipsregular. cutting and needle nose. vi se grip
BATTERYWith proper care, theservice. Proper careremembered.battery willis not diffictprovide lang and satisfactory1ft if a few basic p
MOTOR MOUNTSee Section 5.3 for maintenance of aluminum.OUTBOARD MOTORce. A 4.5 HP motor is perfectlyshaft is recommended. Refer toAn
BELOW THE WATER LINEWith the exception of small crat't that are removed from the water aftereach use, all vessels require same
HAUL OUT PROCEDUREBasically reverse the steps in the launch procedure.and clean the bottom.Thoroughly washIf the boat is to be derig
k~(ß~(..lL1ll,J"T"'O'P l-U~P '- /r1r'I,:,:""~('JI?~li)c'N1, s-'r.1M\""'f'
~upp~CD~U\S~(Z..~I.,::;.~~ tt4.? c:: '\:) ~n?0 I... -;-:'3 c../tiZ-.:D,~ ~I!:'I~~~~I..."'.) ,~c.;-o~'S ~ '=?1
RAISINGTHE l\'lAST2.4.1.4. m.(.
2.4.1.62.4.1.72.52.5.12.5.22.5.32.62.6.12.6.22.6.32.72.82.8.12.92.9.1RiggingInstalling the BoomRigging the RunningPrelaunch ChecksHull Inspectio
'S'-, c...:::..~~
(~\2:.<=. -e=:. 'l I I.J <;\ ~ L t- E ~ ~ 1S."r'L. -A..A.Co)}..:) M_~T(ov;-::;".,t(2..~)~ (.j~ A ~\1"1- &apo
Sc:=.:::r7.~...Ä..,i;.(j,.~~2.-~ '9"7M /'rI1-.j :s. fT'\- ~'iZ-C'I.,::' -v l l., 4(~oCJM-~St ~ \..1.3t'a
"'..~...':\ '.,e';. 0;:',,~.-',,:~..:'0 .:~ 0;'\,~, ~..~...':: ,'" ..° ~:'~i,&qu
INTRODUCTION SECTION 1INTENT OF MANUAL1.1This manual is intended to acquaint you with the various features ofyour yacht and to prov
WARRANTY POLICY11:METRE ONE D~IGNThe 11 :METRE One Design warranty policy is backed by:International One Design Group ABOsterlanggatan 14S
WARRANTY REGISTRATION FORMReturn to:Precision Boat Works1511 18th Avenue Drive EastPalmetto, FL 34221HIN #: PCW 33Date:Dealer:Owner:I, the u
COMMISSIONING SECTION 22.1INTRODUCTIONThe first commissioning of a yacht is essentially the start of the yacht'slire. and the im
KEELINSTALLATIONTbe 11 :METRE is shipped to your dealetinstallation is a very simple procedure.1,600 Ibs. (725 kg) and the hull (w1,8
c)Continue to insert the rudder tpoint the rudder stock is throughrough the top hearing. At this:h the cockpit sole.Slip the thrus
Comments to this Manuals