Craftsman 113.228360 Owner's Manual

Save Thls Manual _'Xor Future Reference• SF RSowner'smanualMODEL NO.113.228360WOOD LATHEit i liiii ,ii lulSerialNumberModel and serialnumbe

assembly,,. J ,,,,WARNING:To avoid Injury from unexpected lathemovement and to provide necessary stability,mountthe lathe to a stationary work bench w

,,Place lathe bed near front of workbench in the posi-tion you want it to be permanently attached. Thefront of lathe bed should be positioned a minimu

9. Fromtheloosepartsbaglocatea114"x1-1/2"hexheadbolt,1/4"fiatwasher,1/4"Iockwasher,and114"hexnut,Placeboltthroughcenterbedmou

STRAIGHTEDGE,\12. Hold straight edge tightly against bed sections. Liftup on bed sections until air gap between straightedge and bed sections disappea

_,. ,, -_ i, HI, H , iHl,,TOOL REST SLIDE LOCKTOOL REST SLIDEMOUNTING AND ASSEMBLINGTOOL REST ASSEMBLY1. From the loose parts find the tool rest slide

TOOL REST LOCK, From the loose parts locate the tool rest and toolrest lock. See illustration for appearance of tool restlock. Set tool rest in tool r

HANDWHEEL3, From the loose parts locate the handwheel andtailstock spindle. Place handwheel into tailstock asillustrated.GROOVE INSPINDLESPINDLEGROOVE

HANDWHEEL10/32" SOCKET HEAD SCREW6, From the loose parts bag locate a 10/32 x 1" sockethead screw, Screw the screw into the back side ofthe

3, Place a 5/32 °' hex wrench through round openingnear power cord on backside of headstock. Inserthex wrench into set screw located 1-1/2"

6. Placestraightedgeagainstspindlepulleysooneendofstraightedgeisjustabovethelargesectionon motorpulley.Withstraightedgetouchingfullfaceof spindlepulle

FULL ONE YEAR WARRANTY ON CRAFTSMAN WOOD LATHEIf within one year from the date of purchase, this Craftsman Wood Lathe fails due to a defectin material

11.Fromtheloosepartslocatea#6 x3/8phillipsheadscrew(seeillustration).Usinga #2 phillips headscrewdriver install this motor cover stop screw, it isloca

3. Check and be sure that inside of headstock andtailstock spindles are clean. Insert spur center intoheadstock spindle and cup center into taitstocks

WARNING: Before using the iathe, test to makesure headstock ls properly secured to lathe bed.Failure to properly secure headstock to lathe bedmay al]o

INSTALLATION AND USE OF ON-OFFSWITCH KEYWARNING: Don't connect power cord to an elec-trical outlet until your lathe is mounted in itsupright posi

basic lathe operationWARNING: To avoid Injury from unexpected start-ing, for your own safety, turn switch "off" andremove plug from power so

BELT TENSION ADJUSTMENT1. Place belt tension adjustment lever in middle oflong slot,BELT TENSIONADJUSTMENT LEVER"SLOT2. Notice which lever suppor

26basic lathe operationsMOUNTING WOOD FOR SPINDLETURNINGWARNING:To avoid Injury from unexpected start-Ing, turn switch "off" and remove swit

12. Adjust the tool rest approximately 1/8" away fromthe corners of the wood and 1/8" above the centerline. Note the angled position of the

GOUGEturning tools! ImSKEW PARTINGTOOL SPEAR POINT FLAT NOSETHE SiX COMMONLY USED CHISEL TYPESmmROUND NOSEA book entitled "Power Tool Know How Ta

If you are removing wood from the diameter of a work-piece (as when turning the face of a faceplate turning)you must use ascraping action only.This is

additional safety instructions for wood turning lathesSafety is a combination of common sense, staying alertand knowing how your lathe works.BEFORE US

HOLDING THE WOODWORKING CHISELIn handling alt turning tools, the handle hand takes anatural position, being nearer or farther from the endof the handl

Sears recommends the following accessoriesITEM CAT. NOWork Bench ... See CatalogDrill Chuck 1/2" Capacity withNo, 1 M,T, Shank

trouble shootingTROUBLE SHOOTING -- MOTORNOTE: Motors used on wood-working tools are particularly susceptible to the accumulationof sawdust and wood c

NOTES33

\\\\\\/tt/$\\\\s_

O1KeyNo.123456789101112131415161718192021222324252628293O313233343536_A,_J,5 LlSl FUH _HAF _ /tAN lz"Wuuu LAIHEMODEL NO_13.228360Always order by

_A/RSowner'smanualSERVICEMODEL NO.113.228360WOOD LATHEHOW TO ORDERREPAIRPARTSIF YOU NEED REPAIRSERVICE OR PARTS:For Repair Service, Cal!this Tol

3) Make sure centers are aligned whentailstock and ram are locked.4) Make sure the spur center and cup centerare firmly seated against the workpiece a

glossary of termsSpur Center (Live Center)Installed in the spindle of the headstock.., supportsthe workpiece on center at the headstock.., transferspo

motor specifications and electrical requirementsPOWER SUPPLYMotor SpecificationsThis wood lathe is designed to use the type motorsupplied withthe unit

unpacking and checking contentsWARNING: To avoid injury from unexpected start-Ing or electrical shock, do not plug the powercord into a source of powe

List of Loose Parts in Bag #507743O Screw Soc. Hex 1/4-20 x 3/8 ... 1p Leckwasher 1/4 ... 7Q Nut Hex 1/4-20 ...

location and function of controls1. ON-OFF SWITCH ... Turns lathe on and off andlocks lathe in off position.2. TOOL REST SLIDE ... Allows the tool r