Craftsman 987.889000 User Manual

OWNER’SMANUALMODEL NO. 987.889000A Caution;Read and Follow All Safety Rules and Instructions Before Operating This Equipment.CRAFTSMAM8 HORSEPOWER 33-

ASSEMBLYSTEP 2: Attach Control RodsWARNINGThe control rods are adjusted at the factory and should not require additional adjustment during ass

ASSEMBLYEEIPin (K) must be in this detent when transmission neutrai is adjusted.• Rotate gear select lever (I, Rg- ures 2-6 & 2-7) clock

ASSEMBLY• Insert hooked end of shift link (P, Figure 2-7) into hole in bottom end of gear select lever (I) and secure with cotter pin (Q). Bend ends

OPERATIONKNOW YOUR EQUIPMENTREAD THIS OWNER’S MANUAL AND ALL SAFETY RULES BEFORE OPERATING YOUR EQUIPMENT. Know the location and function

OPERATIONBlade Drive ControlUse this lever (B, Figure 3-2) to engage drive to the mower blades.To engage the blades, first engage the Operator Presen

OPERATIONWheel Drive ControlUse this lever {D, Figure 3-5) to engage and disengage drive to the wheels.To engage the wheels, first select a fonward or

OPERATIONEngine Thrnttle ControlThis lever (F, Figure 3-8) is used to adjust engine speeds and to stop the engine. Always run engine at fast speed se

OPERATIONBEFORE STARTING ENGINE Add Motor Oil• Only use high quality detergent oil rated with API service classification SR SG or SH. Select the oil&

OPERATIONAd|ust Mowet Cutting HeightThe cutting height can be adjusted from 1 to 4 inches by rotating the Cutting Height Control lever (A, Figure 3-1

OPERATIONSTARTING AND STOPPING THE ENGINEDANGERDo not operate engine In an enclosed area. Engine exhaust contains carbon monoxide, a deadly ga

SAFETY RULESA CAUTION: ALWAYS DISCONNECT SPARK PLUG WIRE AND PLACE WIRE WHERE IT AAA CANNOT CONTACT SPARK PLUG TO PREVENT ACCIDENTAL STARTING WHEN SET

OPERATIONTO ENGAGE THE WHEELS CAUTION• To avoid damaging the transmissio'n, do not shift gears whiie in motion.• To avoid damaging the

OPERATIONMOWING TIPS AND HINTSWARNINGTo avoid injury or property damage:• Before mowing, thoroughly inspect area where mower is to be used and re

OPERATIONBUDE BRAKE CONTROL TESTWhen the Operator Presence Control is released during operation of the mower, the engine does not stop, but the blade

CUSTOMER RESPONSIBILITIESMaintenance ChartINTERVAL* ITEM SERVICEEach useMower Blade As Required-Loose or Missing HardwareTighten or Replace -Belts Che

CUSTOMER RESPONSIBILITIESGENERAL RECOMIVIENDATIONSThe warranty on this equipment does not cover items that have been subjected to operator abuse or ne

CUSTOMER RESPONSIBILITIESAIR CLEANER SERVICEImproper air cleaner maintenance can cause engine damage.SERVICE SCHEDULE:Foam Filter (A, Fig. 5-3): Wash

SERVICE AND ADJUSTMENTSSPARKPLUGInspect the spark plug (Figure 5-4) after every 100 hours of operation. Be sure the gap is set at .03

SERVICE AND ADJUSTMENTSBUDE DRIVE BELT REPLACEMENTFollow this procedure to remove and replace the blade drive belt. An assistant will be need

SERVICE AND ADJUSTMENTSBUDE DRIVE BELT ADJUSTMENTIf the blade drive belt is slipping due to lack of belt tension, follow the steps below.1. Stop engi

SERVICE AND ADJUSTMENTSBLADE DRIVE CONTROL LEVER ADJUSTMENTMake the following adjustment if the Blade Drive Control Lever releases during op

SAFETY RULES18. Always wear safety goggles or safety glasses with side shields when operating mower.19. Watch for traffic when operating near, or wh

SERVICE AND ADJUSTMENTSWHEEL DRIVE BELT ADJUSTMENTThe wheel drive belt requires an adjustment if loss of drive beit tension (slippage) occurs. This i

SERVICE AND ADJUSTMENTSWHEEL BRAKE ADJUSTMEHTThis adjustment may be required if the machine does not hold on a hill with the Operator Presence Control

SERVICE AND ADJUSTMENTSMOWER BLADESExamine mower blades before operation. For efficient mowing, cutting edges of blades should always be kept sharp

SERVtCE AND ADJUSTMENTSBlade InstallationBlades must be installed perpendicular to each other (see Figure 5-17).Install mower blade as shown in Figur

OFF-SEASON STORAGE• stop engine, wait for aii parts to stop moving, and disconnect spark plug wire before performing any storage procedures. Review

TROUBLESHOOTING/ïvWARHINGBefore inspecting, cleaning or servicing the machine, shut off engine, make sure that all moving parts have come

OPERATING AND SAFETY DECALSSAFETY DECALSMake certain all safety decals on this equipment are kept clean and in good condition. The decals are shown {a

CRAFTSMAN 8HP MODEL 987.889000 REPAIR PARTSHANDLEBAR AND CONSOLE ASSEMBLY110Ref. PartDescriptionQty.Ref. PartDescription Qty.111186393Flange Locknut,

CRAFTSMAN 8HP MODEL 987.889000 REPAIR PARTSDRIVE ASSEMBLYTORQUE TO 20-25 FTABS. LOCTITE IN PLACE1S| 1938

CRAFTSMAN 8HP MODEL 987.889000 REPAIR PARTSDRIVE ASSEMBLYRef.Part Description Qty.1*Engine, 8 HP... 121769904Eng

SAFETY RULES6. Keep mower free of grass, leaves or other debris build-up. Clean up oil or fuel spillage. Allow mower to cool before storing.7. After

FRONT FRAME ASSEMBLYCRAFTSMAN 8HP MODEL 987.889000 REPAIR PARTS40

FRONT FRAME ASSEMBLYCRAFTSMAN 8HP MODEL 987,889000 REPAIR PARTSRef. Part1116283031 47 53 58 739495 97100101103104105106 108Description1186393118514711

CRAFTSMAN 8HP MODEL 987.889000 REPAIR PARTSMOWER DECK ASSEMBLY4427LOCTITEINTO, „ PUCE 43 ^22 TORQUE TOl\<k> ' 35 FT. LBS. jn—<s>L

CRAFTSMAN 8HP MODEL 987.889000 REPAIR PARTSMOWER DECK ASSEMBLYRef.Part Description Qty.Ref. Part DescriptionQty21185574 Ball Bearing...

CRAFTSMAN 8HP MODEL 987.889000 REPAIR PARTS Transaxle AssemblyMDOtl Md SERIAL NUMBERS HERE15044

CRAFTSMAN 8HP MODEL 987,889000 REPAIR PARTSTRANSAXLE ASSEMBLYRef.Par!Description Qty.Ref.PartDescription 'Qty1772113Transaxle Cover...

Craftsman 4-Cycle, 8HP Engine (Model 143.988000)CRAFTSMAN 8HP MODEL 987.889000 REPAIR PARTS40041646

CRAFTSMAN 8HP MODEL 987-889000 REPAIR PARTSCraftsman 4-Cycle, 8HP Engine (Model 143.988000) Engine AssemblyRef#Part#Description Qty Ref#Part#Descripti

CRAFTSMAN 8HP MODEL 987.889000 REPAIR PARTSCraftsman 4-Cycie, 8HP Engine (Model 143.988006)CARBURETOR NO. 640126Ref« Part#DescriptionQty.0640126 Carbu

CRAFTSMAN 8HP MODEL 987,889000 REPAIR PARTSCraftsman 4-Cycle, 8HP Engine (Model 143.988000)RECOIL STARTER NO. 590746117"^ I ^7<^v,43 5RetH Par

CONGRATULATIONS on your purchase of a Craftsman 33-lndi Mower. It has been designed, engineered and manufactured to give you the best possibie dependa

NOTES50

NOTES51

OWNER’SMANUALMODEL NO. 987.889000IF YOU NEED REPAIR SERVICE OR PARTS:FOR REPAIR SERVICE CALL THIS TOLL-FREE NUMBER:1-800-4-REPAIR(1-800-473-7247)FOR

TABLE OF CONTENTSACCESSORIES AND ATTACHMENTS...2C OQSERVICE AND ADJUSTMENTS... ^TnRAOF ...26...

ACCESSORIES AND ATTACHMENTSThese accessories and attachments were available when the mower was purchased. They are also available at most Sears retail

CONTENTS OF HARDWARE PACKParts Bag Contents©Flat Washer, 5/16” Qty;4Cotter Pin, 3/32" X 5/8” Qty:6Hex Flange Lock Screw, 5/16”-18 X 3/4” Qty:2Hex

ASSEMBLYRead these instructions in their entirety before you attempt to assemble or operate your new equipment. Your new equipment