Sears Bestl/ZnnmMmOwners ManualGarage Door OpenerModel 139.53626SR - 1/2HP Model 139.53515SR - 1/2HPCAUTIONPLEASE READ THIS MANUAL CAREFULLYFASTEN
InstallationSTEP 1Position and Instali Header BracketInstallation procedures are determined by garage door types. Follow only those instructions which
InstallationSTEP 2 Attach Tee Rail to Header BracketPROCEDURE; Position opener chassis on garage floor below the header bracket. Use packing mat
InstallationSTEP 4 Hang Opener ChassisTHE OPENER CHASSIS MUST BE SECURELY FASTENED TO A STRUCTURAL SUPPORT OF GARAGE.Three representative installati
InstallationAALOCATE WALL CONTROL (OR ANY ADDITIONAL PUSH BUTTONS) WHERE GARAGE DOOR IS VISIBLE, AWAY FROM DOOR AND DOOR HARDWARE AN
InstallationSTEP 7 Install Lights and LensesMake sure antenna wire is bent down before installing lights and lenses.Install a 75 Watt maximum
InstallationQTcp Q Install Door Bracket and Plate^ ^ Follow instructions which apply to your door typo as illustrated below.ATO PREVENT DAMAGE TO LIG
InstallationCTpp -in Connect Door Arm to Trolley^ Follow only those instructions which apply to your door type.SECTIONAL DOOR INSTALLATIONMake sure
AdjustmentSTEP 1 Adjust UP and DOWN LimitsLIMIT ADJUSTMENT settings (left side panel) regulate the points at which the door will stop when moving up o
AdjustmentSTEP 3 Test Safety Reverse SystemATHE SAFETY REVERSE SYSTEM TEST IS IMPORTANT. GARAGE DOOR MUST REVERSE ON CONTACT WITH A ONE IN
Radio ControlsRC.C. rules prohibit adjustments to or modification of receiver and transmitter circuitry except for changini code setting and replacing
start By Reading These Important Safety RulesATHIS SAFETY ALERT SYMBOL MEANS CAUTION — PERSONAL SAFETY OR PROPERTY DAMAGE INSTRUCTION. READ
Having a Problem?SITUATIONReview Pages 2 and 3 Before ProceedingPROBABLE CAUSE & SOLUTIONOPENER DOESN’T OPERATE FROM WALL CONTROL OR TRANSMITTER1.
Having a Problem? (Continued)SITUATIONPROBABLE CAUSE & SOLUTIONDOOR REVERSES FOR NO APPARENT REASON1. Is something obstructing the door? P
Repair PartsRAIL ASSEMBLY PARTS LISTKEYNO.PARTNO. DESCRIPTION11A995Master link kit241B3243Inner trolley w/threaded rod3 41B3244Outer trolley4 1B3117Te
Repair PartsChassis Assembly Parts ListKEY PART NO. NO.DESCRIPTIONKEY PART NO. NO.DESCRIPTION1 31C290 Sprocket cover2 41A2827 Gear and sprocket a
Sears Besf//CRBFTSMRNOwnersManualGarageDoorOpenerModels;139.53626SR139.53515SRHOW TO ORDER REPAIR PARTSNow that you have purchased your Sears G
Operation of Your OpenerCAUTIONBEFORE YOU PROCEED, PLEASE READ THE SAFETY RULES ON PAGE 2 AND OPERATING INSTRUCTIONS ON THIS PAGE CAREFULLY
FEATURES OF YOUR OPENER1. Motor: Permanently lubricated with automatic reset.2. Opener Lights: Turn on and off automatically with ЛУг minute illumin
CARTON CHECK LISTSEARS has packaged your GARAGE DOOR OPENER in two cartons which contain all the parts and hardware Illustrated below
AssemblyTO AVOID INSTALLATION DIFFICULTIES, DO NOT RUN THE GARAGE DOOR OPENER UNTIL INSTRUCTED TO DO SO.STEP 1 Assemble Tee Rail & Attach Cable Pu
AssemblySTEP 2 Install TrolleyAS A TEMPORARY STOP, INSERT A SCREWDRIVER INTO HOLE IN FRONT END OF TEE RAIL AS SHOWN.1. Attach threaded shaft to
AssemblySTEP 4 Install Chain and CableDO NOT REMOVE CHAIN AND CABLE FROM CARTON.Detach cable from side of carton. Remove master links from coin en
AssemblySTEP 5 Tighten the Chain and Cable1/2 InchCAUTION: Keep the chain fivm twisting as nute are turned.PROCEDURE: Thread the inner nut on the trol
Comments to this Manuals