Owner’s ManualCRRFTSMRN8.5 Horse Power26” Two-Stage Track DriveSnow ThrowerModel No.247.885500CAUTION: Before using this product, read this manual and
You may have to loosen the carriage bolts and hex lock nuts which secure the lower chute crank bracket to the extension on the left side of the chute
hardware pack. Make sure to route the cable tie over the drive cable. See Figure 13.• Secure the left turn trigger cable to the lower handle
IMPORTANT: Keep all grease and oil off of thefriction wheel and the drive plate.Shifting Mechanism• Lubricate the shifting mechanism and pivot points
Engine MaintenanceEngine OilOnly use high quality detergent oil rated with API service classification SF, SG or SH. Select the oil’s SAE viscosity gra
SERVICE & ADJUSTMENTSAWARNING: Always stop the engine, disconnect spark plug wire and move it away from the spark plug before performing
upper hole in the shift iever.TractionDriveClutchUpper Hole in Shift LeverSpringWasherHairpiClipShiftLeverChute Distance Control^ Auger ControlFlatWas
off the pulleys. See Figure 25.FrontAuger Drive BeltFigure 25• To remove the front auger drive belt, push the idler pulley to the left and lift front
with the bell washer and hex bolt. See Figure 28.CarburetorAWARNING: If any adjustments are made to the engine while the engine is running (e.g.
OFF-SEASON STORAGEIf your snow thrower is left unused for 30 days or longer, It needs to be prepared for storage. Also, at the end of the snow season,
TROUBLE-SHOOTINGPROBLEMPOSSIBLE CAUSECORRECTIVE ACTIONShift lever not locking into the sixth speed1. Shift rod out of adjustment1. Remove washer and p
TABLE OF CONTENTSContentPageContentPageWarranty Information2Maintenance17Safe Operation Practices3Service & Adjustment20Accessories5 Off-Season St
PARTS LISTSEARS CRAFTSMAN 8.5 H.P. SNOW THROWER MODEL 247.88550026
KeyNo.Part No.1629-00582684-0008A-06373684-00224684-00665684-01026684-01117684-01128710-02629710-044210710-045111710-045912710-059913710-089614 710-10
28
KeyNo.Part No.1611-00532618-00433618-00444 618-01697683-00249684-0014B10684-002112684-003114684-0042B17710-053818710-059919710-060220710-060421710-065
i®© \(fi30
KeyNo.Part No.DescriptionQty.KeyNo.Part No.Description Qty.1631-0032Wheel Assembly idler223750-0547Spacer22684-0009Rod Track Pivot124 750-0909Spacer23
KeyNo.Part No.DescriptionQty.KeyNo.Part No.DescriptionQty.1 05931Bearing Housing119731-1379Chute Adapter12605-5192Spiral Assembly120 732-0611Extension
Ref.No. Part No. DescriptionQty.Ref.No.Part No. DescriptionQty.105896ABracket117 736-0331Washer—Bell 12 629-0071Cord, Extension 118736-0505Washer—Flat
CARBURETORCraftsman Engine Model No. 143.988501 for CraftsmanSnow Thrower Model 247.885500KeyNo.PartNo.Description Qty.0640052Carburetor (Incl. 184 of
SAFE OPERATION PRACTICESAThis symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or proper
Craftsman Engine Model No. 143.988501 for CraftsmanSnow Thrower Model 247.885500298\|£^^328370G36
Craftsman Engine Model No. 143.988501 for CraftsmanSnow Thrower Model 247.885500KeyNo.PartNo.DescriptionQty.KeyNo.PartNo.DescriptionQty.135385Cylinder
Craftsman Engine Model No. 143.988501 for CraftsmanSnow Thrower Model 247.885500Table continued from previous pageKeyNo.PartNo. DescriptionQty.KeyNo.P
Recoil StarterCraftsman Engine Model No. 143.988501 for CraftsmanSnow Thrower Model 247.885500o —-6-4O---------2-----1KeyNo.PartNo.DescriptionQty.0 59
For the repair or repfacement parts you need delivered directly to your homeCall 7 am - 7 pm, 7 days a week1-800-366-PART(1-800-366-7278)For in-home m
Manual Del PropietarioCRRFTSMflrEXPULSOR DE NIEVE 8.5 CABALLOS DE FUERZAPROPULSION DE ORUGA DE DOS ETAPAS DE 26"No. De Modelo247.885500Precaución
TABLA DE CONTENIDOGarantía ...2Operación Segura...
PRACTICAS SEGURAS DE OPERACIONENTRENAMIENTO• Lea cuidadosamente en su totalidad esta guía del propietario antes de tratar de ensamblar u operar esta
Cuando transporte o no esté en uso desconecte la potencia al colector/propulsor.Use sólo aditamentos y accesorios aprobados por el fabricante del expu
ACCESORIOS DEL EXPULSOR DE NIEVEEstos accesorios estaban disponibles cuando se compró el expulsor de nieve. Están también disponibles en
hand in the discharge or collector openings. Use a stick or wooden broom handie to unclog the discharge opening.Take ail possible precautions when lea
CONJUNTO DE FERRETERIA DE FERRETERIADespliegue la ferretería de acuerdo con la Ilustración para fines de Identificación. Las piezas están ilustradas a
ENSAMBLADOCanaletaFigura 1IMPORTANTE; Esta unidad ha sido despachada con aceite del motor pero sin gasolina en el motor.Después del ensamblado, vea la
mismo.• Asegure el orificio del fondo del mango al expulsor de nieve usando pernos hexagonales de 5/16x3/4" de largo y la arandela de seguridad d
• Coloque la palanca de cambios en la posición de sexta (6) velocidad.• Coioque el extremo doblado de la vara de cambio dentro dei orificio en el co
soporte inferior de la manivela de la canaleta a la prolongación del lado izquierdo del conjunto de la canaleta. Vea la Figura 8.de la manivela de la
• Asegure el cable del gatillo de giro izquierdo de la misma manera.• Corte los extremos excesivos de cada amarre de cable.NOTA: El amarre del c
OPERACIONConozca Su Expulsor De NieveANTES DE HACER FUNCIONAR SU EXPULSOR DE NIEVE LEA ESTE MANUAL DEL PROPIETARIO Compare las ilustraciones en este f
Manivela De La CanaletaLa manivela de la canaleta está ubicada del lado izquierdo del expulsor de nieve. Vea la figura 15. Para cambiar la dirección e
Arranque el motor siguiendo las Instrucciones de Arranque.Gire la canaleta de descarga a la dirección deseada, alejada de los observadores y/o edifici
Determine que el cableado de su casa es un sistema de tres conductores conectado a tierra. Si no está seguro, consulte con un electricista licenciado.
ACCESSORIESThese accessories were available when the snow thrower was purchased. They are also available at most Sears retail outlets, catalog and ser
Para Apagar El MotorArrancador Eléctrico:• Antes de apagar el motor para ayudar a secar la humedad, haga funcionar el motor por unos pocos minutos.•
MANTENIMIENTORecomendaciones Generales• Observe siempre las reglas de seguridad al efectuar el mantenimiento.• La garantía en este expulsor de nieve
menos o cada veinticinco horas de funcionamiento con grasa. Puede obtenerse acceso a las levas por debajo del panel del mango.Caja De Engranajes• La
AJUSTESAADVERTENCIA: Antes de efectuar cualquier ajuste o reparación, siempre apague el motor, desconecte el cable de la bujía y aléjelo de la bujía.M
• Inserte el casquillo dentro del orificio superior de la palanca de cambios desde el lado derecho cuando el ajuste es correcto. Asegure con la arand
del armazón debajo del expulsor de nieve.Tirando hacia arriba de la polea intermedia, ruede la correa fuera de las poleas intermedia y del motor y lev
ALMACENAMIENTO DE FUERA DETEMPORADAAADVERTENCIA: Nunca almacene el motor con combustible en el tanque, bajo techo o en áreas mal ventiladas, donde los
TABLA DE LOCALIZACION DE FALLASProblemaCausa(s) posibleAcción CorrectoraEl motor no arranca1. Tanque de combustible vacío,0 combustible rancio.2. Es
Sears se complace en ofrecer a sus clientes servicio de reparación de aparatos electrodomésticos y electrónicos de todas las marcas.En Sears, usted p
HARDWARE PACKLay the hardware pieces from the hardware pack on the figure here and you will have automatically sorted these according to the steps of
ASSEMBLYIMPORTANT: This unit is shipped with engine oil, but without gasoline, in the engine. After assembly, see OPERATION section of this manual fo
thrower using 5/16 x3/4" hex bolt and lock washer from the hardware pack (group A on page 6). Do not tighten at this time. See Figure 2. Lock Was
Attaching Shift Rod• Place the shift lever in the sixth (6) speed position.• Place the bent end of the shift rod into the hole in the shift arm asse
Comments to this Manuals